Quick Installation Guide © 2009 BI Incorporated 8-90-00130-0, Revision A
BI ExacuTrack® One Quick Installation Guide Copyright © 2009, BI Incorporated All Rights Reserved Printed in USA BI prepared this guide for use by BI customers only. All comments concerning the contents of this guide should be directed to BI’s Marketing Department, 6400 Lookout Road, Boulder, CO 80301, USA.
Cleaning & Storage After removing the tracking unit from the client’s ankle, clean the unit by wiping the case with a soft cloth. You can use Lysol as a disinfectant if needed. Do not use Pinesol or any cleaning products containing pine oil, as these solvents may damage the plastic body. Store the tracking unit in its original shipping case. As an alternative, you can clean the tracking unit in a standard dishwasher. Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 4 If you are replacing the battery, insert your cutting tool into each locking mechanism on the backplate. Squeeze your cutting tool to disengage the locking mechanisms. Remove and discard the backplate. Step 5 Using a standard screwdriver, turn the battery hatch counter-clockwise to the unlocked position, and remove the battery hatch. Step 6 Remove the battery from the battery well. To install a new battery, follow steps 1 and 2 under “To assemble the tracking unit” on page 5.
To Remove the Tracking Unit: Steps 1-6 > Warning! Do NOT cut the strap to remove the tracking unit from the client’s ankle. Introduction The ExacuTrack One tracking unit is a GPS device secured around the client’s ankle. This device includes the following features: Step 1 While the tracking unit is still on the client’s ankle, insert a screwdriver into the notched grooves on the locking pins. Turn the screwdriver counterclockwise until the hinge assembly is released.
Parts Removal/Battery Replacement Before assembling the tracking unit, verify that you have the necessary parts: If you discharge a client from the program, the tracking unit must be removed. You may also need to remove the tracking unit if the battery, straps, hinge assembly, or the unit case require replacement. A. Adjustable Strap The following parts are reusable: B. Backplate • Unit Case C. Unit Case • Battery D. Male Hinge • Battery Hatch E. Female Hinge • Fixed Strap F.
Confirmation Assembling: Steps 1-10 Self-Test To Assemble the Tracking Unit > After installation, the tracking unit initiates a series of self-tests to make sure the system is functioning properly. These tests only last approximately 3 seconds. Status Monitoring After successful completion of the self-test, the tracking unit initiates location acquisition and checks for cellular service availability. During this period, the tracking unit also monitors battery and tamper status.
To Assemble the Tracking Unit (cont.) > Step 4 Slide the adjustable strap into the other fiber-optic connection bay. Step 3 Step 5 Using a Phillips screwdriver, secure the straps to the unit case with the provided screws. Place one screw in each strap hole, and turn each screw clockwise until you feel resistance. Step 6 Slide the end of the charging port cover into the slot on the bottom of the unit case. Close the hinge assembly around the straps until the locking holes are aligned.
At taching: Steps 1-4 When attaching the tracking unit to the client, keep the following requirements in mind: • The strap sizing numbers must face outward (away from the leg). • The tracking unit must be in the upright position. To Attach the Tracking Unit > Step 8 Connect the backplate to the back of the unit case, ensuring the battery cover slides into the groove on the bottom of the unit case. You will hear a distinct click when the backplate is properly attached.
Sizing: Steps 1-4 Size the tracking unit while the client is standing. The tracking unit must be installed on the narrowest part of the bare ankle. When properly installed, the tracking unit should meet resistance when rotated around the front and back side of the ankle. To Size the Tracking Unit > Step 1 Step 3 Fixed Strap Wrap the adjustable strap around the client’s ankle and under the fixed strap. Sizing Number Note the sizing number on the adjustable strap that is closest to the fixed strap.
FCC NOTICES CLEANING & STORAGE After the tracking unit from the ankle,approved clean the by the party responsible for compliance 1. removing Changes or modifications notclient’s expressly unitcould by wiping with a soft cloth. You can the use equipment. Lysol as a void the thecase user’s authority to operate disinfectant if needed. Do not use Pinesol or any cleaning products containing pine device oil, as these solvents may damage the plastic body.