Product Info

Basic Operations Basic Operations
1110
Powering On/Off
Turn the 【Power/Volume knob】 clockwise to
switch the transceiver power ON till a click is
heard.
Adjusting the Volume
Rotate the 【Power/Volume knob】 to adjust the
volume. Turn clockwise to increase the volume
and counter-clockwise to decrease the volume.
Enter/Exit Menu
Short Press 【MENU】 Key to enter menu, and
press 【UP/DOWN】 key to select the function.
Press 【MENU】 Key to confirm, Press 【EXIT】
to exit.
A/B Band Switch
In standby, press 【EXIT】 Key to switch A/B
Band. Main Band marked with △.
Dual PTT
Press 【PTT-1】 to transmit in A Band.
Press 【PTT-2】 to transmit in B Band.
VFO/Channel Switch
In standby, long Press 【MENU】 Key to switch
between VFO and channel mode.
If the channel list does not have a valid channel
number, you cannot switch to channel mode.
Side Key
To program the side key function via program
software.
Side key functions include: FM Radio/ Power
Switch/Monitor/Scan/Search Frequency.
Battery Voltage
In standby, long press 【0】 Key to check the
current battery voltage.
Keypad Lock/Unlock
In standby, long press 【*】 Key to lock/unlock
keypad.
Dual Standby
After turn on dual standby function, you can wait
two channels signals from Band A and Band B at
the same time.
Operation: Menu-- Setting- Dual Standby
VOX
This function is not necessary to push the PTT on
the transceiver for a transmission. Transmission is
activated automatically by detecting the radio
voice. When finish speaking, the transmission
automatically terminated and the transceiver will
automatically receive signal. Be sure to adjust the
VOX Gain level to an appropriate sensitivity to
allow smooth transmission.
Operation: Menu---VOX Level--OFF/1/2/3
VOX Delay
When the VOX is enabled, set up the VOX delay to
help to extend the transmission time to avoid
stopping a transmission too early.
Operation: Menu-- Setting-- VOX
Delay---0.5~2S
SOS
SOS function support three modes: On site/Send
sound/Send code.
On Site: The radio emits an alarm tone and does
not send out signals to others.
Send Sound: Transmit the alarm sound through
the signal.
Send Code: Transmit the alarm code through the
signal.
Operation: Long press PF1(flashlight key) to turn
on SOS mode.
Radio Setting: Menu-- Setting --SOS mode.
Flashlight
Short press PF1 to turn on/off flashlight.
Scan
In standby, long press 【#】 key to turn on scan
function, it support channel list scan and frequency
steps scan.
Operation: Menu--Setting--Scan mode--Time/-
Carrier/Search.
Time Operation (TO): Scanning will stop when it
detects an active signal, and after 5s, it resumes
scanning.
Carrier Operation(CO): Scanning will stop when it
detects an active signal, until the active signal
disappears, and after 5s, It resumes scanning.
Search Operation(SE): Scanning will stop after it
detects an active signal.
Note: In channel mode, scanning the channel
numbers in the channel list. In frequency mode,
scanning in frequency steps.
PTT-ID
This feature allows you to know who call you.
Transmit ANI code or DTMF code through DTMF.
DTMF code total 15 groups.
In the PC software--Edit--DTMF setting, each
signal or A/B band can independently select the
call code group to be sent.
In the PC software--Edit--DTMF--ANI Code to
set ANI code.
Press to Send ---Transmit the code while push
the PTT button.
Release to Send---Transmit the code while
release the PTT button.
BOTH---Transmit the code while push or release
the PTT button.
Note: Since the ANI code operation is independent
of the DTMF code. If the ANI code conflicts with
the DTMF code setting, the ANI code is sent.