Instruction manual Digital 9000 System
Table Of Contents
- Digital_9000_Manual_06_2017_EN
- Important safety instructions
- Digital 9000 – System overview
- Delivery includes
- EM 9046 receiver
- EM 9046 CAB cable set
- Antennas and antenna boosters
- GZL 9000 antenna cables
- SKM 9000/SKM 9000 COM radio microphone
- Microphone heads for the SKM 9000 radio microphone
- SK 9000 bodypack transmitter
- Microphones for the SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- CI 1-4 line/instrument cable for the SK 9000 bodypack transmitter
- B 60/B 61 battery packs
- BA 60/BA 61 accupack
- L 60 charger
- Product overview
- EM 9046 receiver
- Antennas and antenna boosters
- GZL 9000 antenna cable
- SKM 9000/SKM 9000 COM radio microphone
- SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- BA 60 accupack
- BA 61 accupack
- B 60 battery pack
- B 61 battery pack
- L 60 charger
- Preparing the EM 9046 receiver for use
- Preparing the A/AB/AD 9000 antennas and/or antenna boosters for use
- Preparing the SKM 9000 radio microphone for use
- Preparing the SK 9000 bodypack transmitter for use
- Preparing the L 60 charger for use
- Cascading several chargers
- Setting up or mounting the charger
- Preparing the Digital 9000 system for use
- Using the EM 9046
- Using the SKM 9000
- Using the SK 9000
- Using the L 60
- Cleaning and maintaining the Digital 9000 system
- If a problem occurs ...
- Specifications
Preparing the Digital 9000 system for use
38 | Digital 9000
Connecting the receiver to the mains
To connect the receiver to the mains:
Set the ON/OFF switch 1 to position “0”.
왘 Connect the supplied mains cable to the 3-pin mains socket 2.
왘 Plug the mains connector into the wall socket.
왘 Set the ON/OFF switch 1 to position “1”.
To disconnect the receiver from the mains:
왘 Set the ON/OFF switch 1 to position “0”.
All daisy chained signals are interrupted, i.e.:
– the antenna signals at the daisy chain outputs G and H,
– the booster supply voltage,
– the signal of the external word clock generator.
왘 Pull out the mains connector from the wall socket to completely discon-
nect the receiver from the mains.
Connecting headphones
왘 First turn the headphone volume control H counterclockwise to the
minimum.
왘 Connect headphones with a ¼” (6.3 mm) stereo jack plug to the head-
phone socket I.
CAUTION
Damage to the device due to electric current!
If you connect the receiver to an unsuitable power supply, this
can cause damage to the device.
왘 Use the supplied mains cable to connect the receiver to the
mains (100 to 240 V AC, 50 or 60 Hz).
왘 Ensure a reliable mains ground connection of the receiver –
especially when you are using multi-outlet power strips or
extension cables.
EM9046
21 HG
EM9046
IH
WARNING
Danger of hearing damage due to high sound pressure levels!
The headphones connected to the headphone socket are capable
of producing very high sound pressure levels, which can cause
permanent hearing damage.
왘 Always turn the headphone volume control H counterclock-
wise to the minimum
– before connecting headphones and putting them on;
– before you change to a different channel.
For information on headphone monitoring of channels, refer to page
84.