ADN-W AM Antenna Module Instruction manual
For your safety For your safety ............................................................................................... 1 DE Contents Package contents .......................................................................................... 2 EN The ADN-W AM antenna module ............................................................... 1 Components required for wireless operation .......................................... 3 Preparing the antenna module for operation ..........................
Package contents Package contents 1 ADN-W AM antenna module with 3 rod antennas (ADN-W AM or ADN-W AM-US version) 1 SDC CBL RJ45-5 system cable, length 5 m 1 thread insert (5/8" to 3/8") 1 instruction manual Intended use Intended use of the products includes • using the products for professional purposes, • having read and understood the safety instructions and the ADN system manual, • using the products within the operating conditions and limitations described in the ADN system manual.
Components required for wireless operation 505553 Controls the conference (wired and wireless 505554 components) and supplies power to the ADN-W AM antenna 505555 module Function 504748 Allows to make contributions to the conference 1 - 10 ADN-W C1 wireless (optional) chairperson unit 504745 Allows to manage the conference ADN-W BA battery pack 504744 Supplies power to wireless conference units ADN-W MIC 15-39 504750 ADN-W MIC 36-29 504751 ADN-W MIC 15-50 504752 ADN-W MIC 36-50 504753 Des
Product overview ADN-W AM Product overview ADN-W AM 6 1 7 6 2 76 7 95 mm : 8 3 4 5 9 : : 8 : 1 A 1 Hole for safety wire 2 Cable grip 7 Antenna coupling ring 8 Mounting holes for wall mounting 3 Output socket 4 Input socket 9 5/8" mounting thread with 3/8" thread insert > Rubber feet 5 Hollow jack socket for connection of optional NT 12-50C power supply 6 Antennas 4 | ADN-W AM A Type plate
Preparing the antenna module for operation DE Preparing the antenna module for operation Always use all 3 antennas to ensure reliable wireless operation. The 3 antennas are connected upon delivery. EN Connecting the antennas ES Radio communication outside the legal requirements! When connecting antennas other than the supplied ones, the transmission power of the conference system may not meet the legal requirements and may cause interference to other radio equipment.
Preparing the antenna module for operation Connecting the antenna module to the mains power supply The antenna module is powered from the ADN CU1 central unit via the SBC CBL RJ45 system cable.
Setting up and positioning the antenna module DE Setting up and positioning the antenna module Danger of injury and material damage! If improperly installed or insufficiently fixed, the antenna module can fall from the wall, ceiling or stand or tip over and can cause injury or material damage. FR EN CAUTION ping by means of a safety wire which is attached to a separate hook.
Setting up and positioning the antenna module CAUTION Danger of intermodulation! If you set up the antenna module and the wireless conference units too close to one another, intermodulation can occur. 왘 Observe a minimum distance: – of 1 m between the antenna module and the wireless conference units and – of 0.5 m between the wireless conference units. ADN-W AM ADN CU1 ADN CU1 ESC ... 75 max. 50 m >1m > 0.5 m > 0.5 m > 0.5 m Transmission range approx.
Ceiling mounting is recommended for rooms with a ceiling height of up to approx. 10 m: EN We recommend using several antenna modules in rooms with obstacles. DE Setting up and positioning the antenna module 왘 Orient the antennas horizontally and at a 90° angle with respect to ES the wireless conference units. FR 왘 Mount the antenna module to the center of the ceiling.
Setting up and positioning the antenna module To minimize restrictions in the transmission range: 왘 Avoid placing the antenna module outside the conference room, behind support columns or boardings or next to other radio equipment. If necessary, use several antenna modules in order to provide optimal antenna coverage.
Connecting the ADN-W AM antenna module to the ADN CU1 central unit DE Connecting the ADN-W AM antenna module to the ADN CU1 central unit RU Optionally, you can also connect the antenna module to the PORT sockets of an ADN PS power supply. It does not matter if you are using a string or ring topology. The antenna module is connected just like a conference unit to the cable string or cable ring.
Switching the antenna module on/off ADN CU1 ADN PS ADN PS PORT I/PORT II PORT I/PORT II PORT I/PORT II 1 2 1 2 1 2 OUT ... 20 IN IN IN ... 20 ... 20 OUT OUT Switching the antenna module on/off The antenna module is connected to the ADN CU1 central unit and automatically switches on when the central unit is switched on. To switch the antenna module on: 왘 Set the on/off switch 1 of the ADN CU1 central unit to position “I”. The central unit switches on and its display panel lights up.
Configuring the wireless components DE Configuring the wireless components 왘 Use only radio frequencies and transmission powers that are FR Risk of violation of legal requirements! If you are using radio frequencies and transmission powers that cannot be used license-free in your country, there is a risk of violation of legal requirements. EN CAUTION approved and legal in your country. In some countries/regions (e.g. Canada), the use of wireless components operating in the 5.15 to 5.
Cleaning and maintaining the antenna module – Closed access mode (“Wireless Menu” > “Access Mode” > “Closed”) Only wireless conference units whose serial numbers are listed in a participant list can be used in the wireless conference. If several wireless conferences are held simultaneously, the closed access mode ensures that the wireless conference units connect to the correct conference system.
Specifications ADN-W AM EMC Radio Safety EN 301489-1/-17 EN 300328 EN 301893 EN 300440-1/-2 EN 60065 FR Approved by EN Europe DE In compliance with 47 CFR Part 15 FCC ID: DMOADNWAM Canada CAN ICES-3(B)/NMB-3(B) Industry Canada RSS 210 IC: 2099A-ADNWAM D 12-0044 202 3935-15-7356 ZH Brazil Japanese Radio Law and Japanese Telecommunications Business Law Compliance This device is granted pursuant to the Japanese Radio Law ( 電波法 ) and the Japanese Telecommunications Business Law ( 電気通信事 業法 ).
Specifications ADN-W AM Statements regarding the FCC and Industry Canada rules This device complies with part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany www.sennheiser.com Publ.
