ADN Conference Manager - Installation instructions

ManualsBrandsSennheiser ManualsAudio EquipmentADN-Software „Conference Manager"

Table Of Contents

Preparing the Windows version of the software for use

1|Installation Conference Manager

Preparing the Windows version of the software for use

System requirements

Installing the “Conference Manager” software

To install the software, you require administrator rights.

왘 Close all running applications.

왘 Start the “ADNSetup.exe” file in the “Software/ADN System Software” folder

on the enclosed DVD-ROM.

A confirmation prompt appears:

Component

Requirement

Processor Intel Pentium 4 or AMD Athlon XP, 2 GHz or more

RAM Min. 1 GB, depending on your operating system

Hard disk Min. 500 MB free hard disk memory

Drives DVD-ROM

Interfaces/network Ethernet 100 MBit/s

TCP/IP internet protocol Internet Protocol version 4 (IPv4)

Screen Minimum resolution: 800 x 600 pixels

Recommended: 1024 x 768 pixels

Operating system

Microsoft Windows XP Professional with SP 3

Microsoft Windows Vista mit SP2

Microsoft Windows 7

Microsoft Windows 8

The following steps describe the installation of the “Conference Manager”

software on a PC running Windows 8. The installation on a PC running Win-

dows XP, Windows Vista or Windows 7 is performed in a similar way.

Summary of content (7 pages)

PAGE 1
Preparing the Windows version of the software for use System requirements Component Requirement Processor Intel Pentium 4 or AMD Athlon XP, 2 GHz or more RAM Min. 1 GB, depending on your operating system Hard disk Min.
PAGE 2
왘 Click the “Next” button. After you have accepted the license agreement, a confirmation prompt appears: 왘 Untick the “ADN System Update” check box. 왘 Make sure that the “ADN Conference Manager (local)” check box is ticked. 왘 Click the “Next” button. A summary of the selected installation settings is displayed: 왘 Confirm this summary by clicking the “Install” button.
PAGE 3
왘 Click the “Next” button. A selection window for specifying the installation location appears: 왘 Use the default or select an installation path. 왘 Click the “Next” button. A summary of the selected installation settings is displayed: 왘 Confirm this summary by clicking the “Next” button. The installation is performed and a confirmation appears: 왘 Click the “Close” button. A confirmation appears. 왘 Click the “Finish” button. The software has been successfully installed.
PAGE 4
Information on the firmware update of the ADN products (“ADN System Update”) can be found in the “ADN System Software Setup” manual included on the DVD-ROM (supplied with the central unit) or at www.sennheiser.com. Uninstalling the “Conference Manager” software You can uninstall the “Conference Manager” software using the installation wizard on the DVD-ROM or using the Windows Control Panel (category “Add or Remove Programs”, entry “Sennheiser Conference Manager”).
PAGE 5
Adjusting the network settings To enable communication between the central unit and the Windows PC: 왘 Make sure that the network communication between the central unit and the Windows PC is not blocked by a proxy server and/or a firewall. Ports 53248, 53249, 53250, 53251, 53252 are used for communication and port 21 is used for FTP transfer. 왘 Ask your system administrator if a static IP address with a default gateway is to be used or if the IP address is to be assigned dynamically.
PAGE 6
왘 Click “Network Connections” in the right column. The “Network Connections” window appears. 왘 Double-click “Local Area Connection”. The “Local Area Connection Status” window appears. 왘 Click the “Properties” button. The “Local Area Connection Properties” window appears. 왘 In the “This connection uses the following items” box, scroll to the bottom. 왘 Double-click “Internet Protocol (TCP/IP)”. The “Internet Protocol (TCP/IP) Properties” window appears.
PAGE 7
B Static IP address The Windows PC is assigned a static IP address with a default gateway in the network. Settings to be adjusted via the central unit (see „Adjusting further settings – Settings” in the System instruction manual): 왘 On the central unit, call up the “IP Mode” menu item. Main Menu Settings Network IP Mode 왘 Select “Static IP”.