Instruction manual Digital 9000 System
Table Of Contents
- Digital_9000_Manual_06_2017_EN
- Important safety instructions
- Digital 9000 – System overview
- Delivery includes
- EM 9046 receiver
- EM 9046 CAB cable set
- Antennas and antenna boosters
- GZL 9000 antenna cables
- SKM 9000/SKM 9000 COM radio microphone
- Microphone heads for the SKM 9000 radio microphone
- SK 9000 bodypack transmitter
- Microphones for the SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- CI 1-4 line/instrument cable for the SK 9000 bodypack transmitter
- B 60/B 61 battery packs
- BA 60/BA 61 accupack
- L 60 charger
- Product overview
- EM 9046 receiver
- Antennas and antenna boosters
- GZL 9000 antenna cable
- SKM 9000/SKM 9000 COM radio microphone
- SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- BA 60 accupack
- BA 61 accupack
- B 60 battery pack
- B 61 battery pack
- L 60 charger
- Preparing the EM 9046 receiver for use
- Preparing the A/AB/AD 9000 antennas and/or antenna boosters for use
- Preparing the SKM 9000 radio microphone for use
- Preparing the SK 9000 bodypack transmitter for use
- Preparing the L 60 charger for use
- Cascading several chargers
- Setting up or mounting the charger
- Preparing the Digital 9000 system for use
- Using the EM 9046
- Using the SKM 9000
- Using the SK 9000
- Using the L 60
- Cleaning and maintaining the Digital 9000 system
- If a problem occurs ...
- Specifications
Digital 9000 | 77
Using the EM 9046
To synchronize the settings with your transmitters via infra-red:
왘 Select
one of the channels 1–8.
왘 Switch on the transmitter to which you want to assign this channel.
왘 Press the button J on the EM 9046.
The receiver switches to synchronization mode and the LED B
flashes.
왘 Place the transmitter’s infra-red interface in front of the infra-red
interface D of the receiver. Maintain a distance of approx. 10–20 cm
between the infra-red interfaces.
The transmitter and receiver are synchronized:
– After pressing the button J, the receiver’s infra-red interface
searches for a suitable transmitter infra-red signal for 12 seconds.
– You can interrupt the synchronization at any time by pressing the
button J again.
– If a problem occurs during the synchronization process, read the
chapter “If a problem occurs ...” on page 110.
왘 Repeat the above steps for the remaining transmitters.
Main menu “Channel setup”
To get into the main menu:
왘 Select the “ch” operating mode.
왘 Select one or several channels (see page 52).
왘 Call up the menu items described in the following and adjust your set-
tings.
왘 Press the button to store your settings.
왘 Synchronize your settings via infra-red (see page 77).
“Frequency” – Selecting a frequency preset or setting a frequency
manually
Via the “Frequency” menu item, you can select a frequency preset for the
active booster frequency range or set the frequency manually. In the
above diagram, range “A1” is active. The frequency range is from “470-
494 MHz”. For information on how to activate a booster frequency range,
refer to page 59.
왘 Either select a frequency preset (“A1.1” ... “A1.40” in the above dia-
gram) or set the frequency manually (“U”). If you set the frequency
manually, make sure to set a frequency within the current 24 MHz
booster frequency range and maintain a frequency spacing of 600 kHz
to avoid intermodulation interference.
If no channel is selected, “Please select Channel” is displayed in the
menu selection.
Preset A1.1 Freq 470 . 200 MHz
Range: 470 - 494 MHz
frequency