Instruction manual ew 100 G4
Table Of Contents
- Overview
- ew 100 G4 series products
- Accessories
- The frequency bank system
- Installing and starting up ew 100 G4 series devices
- Installing the EM 100 G4
- Installing the SKM 100 G4
- Installing the SK 100 G4
- Installing the ASA 214
- Using ew 100 G4 series devices
- Using the EM 100 G4
- Operating elements on the front of the device
- Switching the EM 100 G4 on and off
- Muting the audio output
- Lock-off function
- Displays on the EM 100 G4 display panel
- Buttons for navigating through the menu
- Home screen
- Setting options in the menu
- Menu structure
- Squelch menu item
- Easy Setup menu item
- Frequency Preset menu item
- Name menu item
- AF Out menu item
- Equalizer menu item
- Auto Lock menu item
- Advanced menu item
- Advanced -> Tune menu item
- Advanced -> Guitar Tuner menu item
- Advanced -> Pilot Tone menu item
- Advanced -> LCD Contrast menu item
- Advanced -> Reset menu item
- Advanced -> Software Revision menu item
- Using the SKM 100 G4
- Operating elements of the SKM 100 G4 handheld transmitter
- Switching the SKM 100 G4 handheld transmitter on and off
- Muting the handheld transmitter (AF mute)
- Deactivating the RF signal (RF mute)
- Lock-off function
- Displays on the SKM 100 G4 handheld transmitter display panel
- Buttons for navigating the SKM 100 G4 menu
- Setting options in the menu
- Sensitivity menu item
- Frequency Preset menu item
- Name menu item
- Auto Lock menu item
- Advanced menu item
- Advanced > Tune menu item
- Advanced > Mute Mode menu item (SKM 100 G4-S only)
- Advanced > Pilot Tone menu item
- Advanced > LCD Contrast menu item
- Advanced > Reset menu item
- Advanced > Software Revision menu item
- Using the SK 100 G4
- Operating elements of the SK 100 G4 bodypack transmitter
- Switching the SK 100 G4 bodypack transmitter on and off
- Muting the bodypack transmitter (AF mute)
- Deactivating the RF signal (RF mute)
- Lock-off function
- Displays on the SK 100 G4 bodypack transmitter display panel
- Buttons for navigating the SK 100 G4 menu
- Setting options in the menu
- Sensitivity menu item
- Frequency Preset menu item
- Name menu item
- Auto Lock menu item
- Advanced menu item
- Advanced > Tune menu item
- Advanced > Mute Mode menu item
- Advanced > Cable Emulation menu item
- Advanced > Pilot Tone menu item
- Advanced > LCD Contrast menu item
- Advanced > Reset menu item
- Advanced > Software Revision menu item
- Establishing a radio link
- Synchronizing devices
- Using the ASA 214
- Overview
- Product variants
- Frequency tables
- Specifications
- Pin assignment
- Cleaning and maintenance
Using the ASA 214
125
Switching the ASA 214 on and off
To switch on the antenna splitter:
▷ Short-press the STANDBY button.
The antenna splitter switches on and the power LED turns green.
The RF signals of the connected antennas are distributed to all con-
nected receivers.
To switch the antenna splitter to standby mode:
▷ Press the STANDBY button for approx. 2 seconds.
The LED turns off. The connected antenna amplifiers are switched off.
Connected receivers are switched off if they draw their supply voltage
from the BNC sockets A1 to A4 (see “Connecting receivers to the
ASA 214”).
To fully switch off the antenna splitter:
▷ Disconnect the antenna splitter from the power supply system by un-
plugging the power supply unit from the wall socket.
The LED turns off.