Instruction manual - Digital 6000 (v4.0)
Table Of Contents
- The Digital 6000 Series
- Products in the Digital 6000 series
- Accessories
- Installing Digital 6000 series devices
- Installing the EM 6000
- Connectors on the rear of the device
- Connecting/disconnecting the EM 6000 to/from the power supply system
- Connecting the EM 6000 to a network
- Outputting analog audio signals
- Outputting digital audio signals
- Outputting audio via a Dante™ network (EM 6000 DANTE only)
- Connecting the word clock
- Connecting remote antennas
- Connecting rod antennas
- Installing the EM 6000 in a rack
- Installing the SKM 6000
- Installing the SK 6000
- Installing the SK 6212
- Installing the L 6000 | LM 6060 | LM 6061 | LM 6062
- Using Digital 6000 series devices
- Using the EM 6000
- Operating elements on the front of the device
- Switching the EM 6000 on and off
- Displays on the EM 6000 display panel
- Buttons for navigating through the menu
- Home screen
- Muting the audio signal
- Setting options in the menu
- Menu structure
- Frequency menu item
- Name menu item
- Sync Settings menu item
- Encryption menu item
- Command Mode menu item
- Scan & Auto-Setup menu item
- Walktest menu item
- AF Output menu item
- Test Tone menu item
- Bank Edit menu item
- System menu item
- System -> Transmission Mode menu item
- System -> Wordclock menu item
- System -> Network menu item
- System -> Device ID menu item
- System -> Dante Settings (only EM 6000 DANTE) menu item
- System -> Booster Feed menu item
- System -> Brightness menu item
- System -> Auto Setup menu item
- System -> Info menu item
- System -> Hardware menu item
- System -> Help menu item
- System -> TX Update menu item
- System -> Reset menu item
- Using the headphone output
- Updating the firmware of the receiver
- Updating the firmware of the Dante™ interface
- Status messages
- Using the SKM 6000
- Using the SK 6000
- Using the SK 6212
- Using the L 6000
- Switching the L 6000 on and off
- Charging rechargeable batteries
- Meaning of the LEDs on the L 6000 charger and LM 6060, LM 6061 and LM 6062 charging modules
- Preparing rechargeable batteries for storage (storage mode)
- Resetting settings (factory reset)
- Updating the firmware
- Operating the L 6000 via a network
- Establishing a radio link
- Synchronizing devices
- Overview
- Recommendations for using antennas
- Equidistant frequency grid
- Link Density mode
- Word clock scenarios for digital audio (AES3 and Dante™)
- Overview
- Product variants
- Specifications
- Cleaning and maintenance
Using the EM 6000
123
Step 1: Set the transmission mode in the receiver
To open the Transmission Mode menu item:
▷ Turn the jog dial in the System menu item until the Transmission
Mode menu item appears in the selection frame.
▷ Press the jog dial to open the menu.
The display shows you the option that is currently selected.
►
▷ Turn the jog dial to choose between the following options:
• LR: Select this option if you want to use Long Range mode.
• LD: Select this option if you want to use Link Density mode.
▷ Press the SAVE button to save the setting.
When changing the transmission mode, a message is displayed to in-
form you that the change will be made to both of the receiver’s chan-
nels.
▷ Press the SAVE button again to confirm this message and the change
in transmission mode.
The receiver restarts and switches to the selected transmission mode.
If the receiver and/or the transmitter are restored to the factory set-
tings, LR mode will be active following the reset.
Step 2: Synchronize the transmission mode on the transmitter
To also set the selected transmission mode in the transmitters, they must
now be synchronized with the receiver. It is not possible to set the trans-
mission mode in the menu of the transmitter itself.
▷ Press the SYNC button for the required channel on the receiver and
hold the transmitter in front of the infrared interface of the receiver to
synchronize the transmission mode on the transmitter.
For more detailed information on synchronizing transmitters and re-
ceivers, see „Synchronizing devices“.