Instruction manual - Digital 6000 (v4.0)
Table Of Contents
- The Digital 6000 Series
- Products in the Digital 6000 series
- Accessories
- Installing Digital 6000 series devices
- Installing the EM 6000
- Connectors on the rear of the device
- Connecting/disconnecting the EM 6000 to/from the power supply system
- Connecting the EM 6000 to a network
- Outputting analog audio signals
- Outputting digital audio signals
- Outputting audio via a Dante™ network (EM 6000 DANTE only)
- Connecting the word clock
- Connecting remote antennas
- Connecting rod antennas
- Installing the EM 6000 in a rack
- Installing the SKM 6000
- Installing the SK 6000
- Installing the SK 6212
- Installing the L 6000 | LM 6060 | LM 6061 | LM 6062
- Using Digital 6000 series devices
- Using the EM 6000
- Operating elements on the front of the device
- Switching the EM 6000 on and off
- Displays on the EM 6000 display panel
- Buttons for navigating through the menu
- Home screen
- Muting the audio signal
- Setting options in the menu
- Menu structure
- Frequency menu item
- Name menu item
- Sync Settings menu item
- Encryption menu item
- Command Mode menu item
- Scan & Auto-Setup menu item
- Walktest menu item
- AF Output menu item
- Test Tone menu item
- Bank Edit menu item
- System menu item
- System -> Transmission Mode menu item
- System -> Wordclock menu item
- System -> Network menu item
- System -> Device ID menu item
- System -> Dante Settings (only EM 6000 DANTE) menu item
- System -> Booster Feed menu item
- System -> Brightness menu item
- System -> Auto Setup menu item
- System -> Info menu item
- System -> Hardware menu item
- System -> Help menu item
- System -> TX Update menu item
- System -> Reset menu item
- Using the headphone output
- Updating the firmware of the receiver
- Updating the firmware of the Dante™ interface
- Status messages
- Using the SKM 6000
- Using the SK 6000
- Using the SK 6212
- Using the L 6000
- Switching the L 6000 on and off
- Charging rechargeable batteries
- Meaning of the LEDs on the L 6000 charger and LM 6060, LM 6061 and LM 6062 charging modules
- Preparing rechargeable batteries for storage (storage mode)
- Resetting settings (factory reset)
- Updating the firmware
- Operating the L 6000 via a network
- Establishing a radio link
- Synchronizing devices
- Overview
- Recommendations for using antennas
- Equidistant frequency grid
- Link Density mode
- Word clock scenarios for digital audio (AES3 and Dante™)
- Overview
- Product variants
- Specifications
- Cleaning and maintenance
Using the SKM 6000
149
Lock menu item
In this menu item, you can activate or deactivate the lock-off for
the transmitter.
Alternatively, you can also adjust the lock-off in the receiver and synchro-
nize it with the transmitter. See „Sync Settings menu item“.
To enable the lock-off:
▷ Open the Lock menu item and set the value to On.
▷ Save your entry by pressing the SET button.
The automatic lock-off function will remain activated.
To temporarily deactivate the lock function:
▷ Press the ON/OFF/ESC button.
The message LOCKED is shown on the display.
▷ Press the UP or DOWN button.
The message UNLOCK is shown on the display.
▷ Press the SET button.
The lock-off function is now temporarily disabled.
You can change settings as needed in the menu. The lock-off function
is reactivated after 10 seconds of inactivity.
To disable the lock-off:
▷ Open the Lock menu item and set the value to Off.
▷ Save your entry by pressing the SET button.
The automatic lock-off function will remain disabled.
Test Tone menu item
In this menu item, you can activate a 1 kHz test tone that the trans-
mitter transmits instead of the input signal. Use this function to
level out the system and during the walk test.
LED Mode menu item
In this menu item, you can set the behavior of the blue LED in the
ON/OFF/ESC button.
ON: The blue LED remains continuously lit.
LCKOFF: The blue LED switches off once the lock-off function is enabled.
Reset menu item
In this menu item, you can reset the transmitter settings to the fac-
tory settings.