Instruction manual - Digital 6000 (v4.0)
Table Of Contents
- The Digital 6000 Series
- Products in the Digital 6000 series
- Accessories
- Installing Digital 6000 series devices
- Installing the EM 6000
- Connectors on the rear of the device
- Connecting/disconnecting the EM 6000 to/from the power supply system
- Connecting the EM 6000 to a network
- Outputting analog audio signals
- Outputting digital audio signals
- Outputting audio via a Dante™ network (EM 6000 DANTE only)
- Connecting the word clock
- Connecting remote antennas
- Connecting rod antennas
- Installing the EM 6000 in a rack
- Installing the SKM 6000
- Installing the SK 6000
- Installing the SK 6212
- Installing the L 6000 | LM 6060 | LM 6061 | LM 6062
- Using Digital 6000 series devices
- Using the EM 6000
- Operating elements on the front of the device
- Switching the EM 6000 on and off
- Displays on the EM 6000 display panel
- Buttons for navigating through the menu
- Home screen
- Muting the audio signal
- Setting options in the menu
- Menu structure
- Frequency menu item
- Name menu item
- Sync Settings menu item
- Encryption menu item
- Command Mode menu item
- Scan & Auto-Setup menu item
- Walktest menu item
- AF Output menu item
- Test Tone menu item
- Bank Edit menu item
- System menu item
- System -> Transmission Mode menu item
- System -> Wordclock menu item
- System -> Network menu item
- System -> Device ID menu item
- System -> Dante Settings (only EM 6000 DANTE) menu item
- System -> Booster Feed menu item
- System -> Brightness menu item
- System -> Auto Setup menu item
- System -> Info menu item
- System -> Hardware menu item
- System -> Help menu item
- System -> TX Update menu item
- System -> Reset menu item
- Using the headphone output
- Updating the firmware of the receiver
- Updating the firmware of the Dante™ interface
- Status messages
- Using the SKM 6000
- Using the SK 6000
- Using the SK 6212
- Using the L 6000
- Switching the L 6000 on and off
- Charging rechargeable batteries
- Meaning of the LEDs on the L 6000 charger and LM 6060, LM 6061 and LM 6062 charging modules
- Preparing rechargeable batteries for storage (storage mode)
- Resetting settings (factory reset)
- Updating the firmware
- Operating the L 6000 via a network
- Establishing a radio link
- Synchronizing devices
- Overview
- Recommendations for using antennas
- Equidistant frequency grid
- Link Density mode
- Word clock scenarios for digital audio (AES3 and Dante™)
- Overview
- Product variants
- Specifications
- Cleaning and maintenance
Using the SK 6000
156
switches from the frequency preset set up to now to the frequency preset
U, and sends a radio signal to the set frequency.
Observe the general requirements and restrictions for using frequencies at
the following address:
www.sennheiser.com/frequency-information
Preset menu item
This menu item displays the frequency preset U together with its
corresponding frequency. You cannot configure any settings here.
Name menu item
In this menu item, you can set a freely selectable name for the
transmitter. The name can be up to eight characters long.
If you enter a name for the radio link in the Name menu item on the re-
ceiver and synchronize the receiver with a transmitter, the name en-
tered in the transmitter is overwritten with the name entered in the
receiver.
Gain menu item
In this menu item, you can adjust the input gain in 3 dB steps.
Alternatively, you can also adjust the input gain in the receiver and
synchronize it with the transmitter. See „Sync Settings menu item“.
The range in which the input can be adjusted varies depending on the
microphone or line-cable used.
Low Cut menu item
In this menu item, you can adjust the value for the low cut filter.
Setting: 30 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz
Alternatively, you can also adjust the low cut filter in the receiver and syn-
chronize it with the transmitter. See „Sync Settings menu item“.
Cable menu item
In this menu item, you can emulate instrument cable lengths:
•Line
•Type 1
•Type 2
•Type 3
Alternatively, you can also configure the cable emulator in the receiver and
synchronize it with the transmitter. See „Sync Settings menu item“.