Instruction manual - Digital 6000 (v4.0)
Table Of Contents
- The Digital 6000 Series
- Products in the Digital 6000 series
- Accessories
- Installing Digital 6000 series devices
- Installing the EM 6000
- Connectors on the rear of the device
- Connecting/disconnecting the EM 6000 to/from the power supply system
- Connecting the EM 6000 to a network
- Outputting analog audio signals
- Outputting digital audio signals
- Outputting audio via a Dante™ network (EM 6000 DANTE only)
- Connecting the word clock
- Connecting remote antennas
- Connecting rod antennas
- Installing the EM 6000 in a rack
- Installing the SKM 6000
- Installing the SK 6000
- Installing the SK 6212
- Installing the L 6000 | LM 6060 | LM 6061 | LM 6062
- Using Digital 6000 series devices
- Using the EM 6000
- Operating elements on the front of the device
- Switching the EM 6000 on and off
- Displays on the EM 6000 display panel
- Buttons for navigating through the menu
- Home screen
- Muting the audio signal
- Setting options in the menu
- Menu structure
- Frequency menu item
- Name menu item
- Sync Settings menu item
- Encryption menu item
- Command Mode menu item
- Scan & Auto-Setup menu item
- Walktest menu item
- AF Output menu item
- Test Tone menu item
- Bank Edit menu item
- System menu item
- System -> Transmission Mode menu item
- System -> Wordclock menu item
- System -> Network menu item
- System -> Device ID menu item
- System -> Dante Settings (only EM 6000 DANTE) menu item
- System -> Booster Feed menu item
- System -> Brightness menu item
- System -> Auto Setup menu item
- System -> Info menu item
- System -> Hardware menu item
- System -> Help menu item
- System -> TX Update menu item
- System -> Reset menu item
- Using the headphone output
- Updating the firmware of the receiver
- Updating the firmware of the Dante™ interface
- Status messages
- Using the SKM 6000
- Using the SK 6000
- Using the SK 6212
- Using the L 6000
- Switching the L 6000 on and off
- Charging rechargeable batteries
- Meaning of the LEDs on the L 6000 charger and LM 6060, LM 6061 and LM 6062 charging modules
- Preparing rechargeable batteries for storage (storage mode)
- Resetting settings (factory reset)
- Updating the firmware
- Operating the L 6000 via a network
- Establishing a radio link
- Synchronizing devices
- Overview
- Recommendations for using antennas
- Equidistant frequency grid
- Link Density mode
- Word clock scenarios for digital audio (AES3 and Dante™)
- Overview
- Product variants
- Specifications
- Cleaning and maintenance
Using the SK 6212
166
Lock menu item
In this menu item, you can activate or deactivate the lock-off for the trans-
mitter.
Alternatively, you can also adjust the lock-off in the receiver and synchro-
nize it with the transmitter. See „Sync Settings menu item“.
To enable the lock-off:
▷ Open the Lock menu item and set the value to On.
▷ Save your entry by pressing the SET button.
The automatic lock-off function will remain activated.
The display switches off.
To temporarily deactivate the lock function (TEMP UNLOCK):
▷ Press the ON/OFF/ESC button.
The display is reactivated.
▷ Press the ON/OFF/ESC button again.
The message LOCKED is shown on the display.
▷ Press the UP or DOWN button.
The message UNLOCK is shown on the display.
▷ Press the SET button.
The lock-off function is now temporarily disabled.
You can change settings as needed in the menu. The lock-off function
is reactivated after 10 seconds of inactivity.
To completely deactivate the lock-off function:
▷ Open the Lock menu item and set the value to Off.
▷ Save your entry by pressing the SET button.
The automatic lock-off function will remain disabled.
Test Tone menu item
In this menu item, you can activate a 1 kHz test tone that the transmitter
transmits instead of the input signal. Use this function to level out the sys-
tem and during the walk test.
Power LED menu item
In this menu item, you can set the behavior of the LED above the SK 6212’s
display and the ON/OFF button.
On: The LED remains continuously lit.
Lock off: The LED switches off once the lock-off function is enabled.