Instruction manual - Digital 6000 (v4.0)
Table Of Contents
- The Digital 6000 Series
- Products in the Digital 6000 series
- Accessories
- Installing Digital 6000 series devices
- Installing the EM 6000
- Connectors on the rear of the device
- Connecting/disconnecting the EM 6000 to/from the power supply system
- Connecting the EM 6000 to a network
- Outputting analog audio signals
- Outputting digital audio signals
- Outputting audio via a Dante™ network (EM 6000 DANTE only)
- Connecting the word clock
- Connecting remote antennas
- Connecting rod antennas
- Installing the EM 6000 in a rack
- Installing the SKM 6000
- Installing the SK 6000
- Installing the SK 6212
- Installing the L 6000 | LM 6060 | LM 6061 | LM 6062
- Using Digital 6000 series devices
- Using the EM 6000
- Operating elements on the front of the device
- Switching the EM 6000 on and off
- Displays on the EM 6000 display panel
- Buttons for navigating through the menu
- Home screen
- Muting the audio signal
- Setting options in the menu
- Menu structure
- Frequency menu item
- Name menu item
- Sync Settings menu item
- Encryption menu item
- Command Mode menu item
- Scan & Auto-Setup menu item
- Walktest menu item
- AF Output menu item
- Test Tone menu item
- Bank Edit menu item
- System menu item
- System -> Transmission Mode menu item
- System -> Wordclock menu item
- System -> Network menu item
- System -> Device ID menu item
- System -> Dante Settings (only EM 6000 DANTE) menu item
- System -> Booster Feed menu item
- System -> Brightness menu item
- System -> Auto Setup menu item
- System -> Info menu item
- System -> Hardware menu item
- System -> Help menu item
- System -> TX Update menu item
- System -> Reset menu item
- Using the headphone output
- Updating the firmware of the receiver
- Updating the firmware of the Dante™ interface
- Status messages
- Using the SKM 6000
- Using the SK 6000
- Using the SK 6212
- Using the L 6000
- Switching the L 6000 on and off
- Charging rechargeable batteries
- Meaning of the LEDs on the L 6000 charger and LM 6060, LM 6061 and LM 6062 charging modules
- Preparing rechargeable batteries for storage (storage mode)
- Resetting settings (factory reset)
- Updating the firmware
- Operating the L 6000 via a network
- Establishing a radio link
- Synchronizing devices
- Overview
- Recommendations for using antennas
- Equidistant frequency grid
- Link Density mode
- Word clock scenarios for digital audio (AES3 and Dante™)
- Overview
- Product variants
- Specifications
- Cleaning and maintenance
Products in the Digital 6000 series
4
EM 6000 | EM 6000 DANTE 2-channel receiver
►
The digital 2-channel receiver works with a switching bandwidth of
244 MHz (470 to 714 MHz), which is covered by three transmitter versions.
For larger 4-channel systems, you can cascade up to EM 6000s without us-
ing additional antenna splitters and you then require only one pair of anten-
nas.
The 2-channel receiver is available in 2 variants:
• EM 6000
• EM 6000 DANTE
The EM 6000 DANTE variant is identical in construction to the EM 6000.
The only difference is that it also has an integrated Dante™ interface (Audi-
nate Brooklyn II) for connecting the device to a Dante™ network. Two
modes are supported for the two Dante™ sockets: Redundant and Through.
▷ See „EM 6000 | EM 6000 DANTE product variants“
You can find more detailed information about the EM 6000 in the fol-
lowing sections:
▷ Installation: „Installing the EM 6000“
▷ Operation: „Using the EM 6000“
▷ Specifications: „EM 6000“ or „EM 6000 DANTE“
Package contents
• 1 EM 6000 or EM 6000 DANTE 2-channel receiver
• 1 mains cables (EU, UK, or US variant)
•2 antennas
• 2 antenna cables (BNC, 50 Ω)
• 4 rubber feet
•1 quick guide
• 1 manual with safety instructions
• 1 manual with technical data and manufacturer declarations