Users Manual
Table Of Contents
- Digital_9000_Manual_06_2017_EN
- Important safety instructions
- Digital 9000 – System overview
- Delivery includes
- EM 9046 receiver
- EM 9046 CAB cable set
- Antennas and antenna boosters
- GZL 9000 antenna cables
- SKM 9000/SKM 9000 COM radio microphone
- Microphone heads for the SKM 9000 radio microphone
- SK 9000 bodypack transmitter
- Microphones for the SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- CI 1-4 line/instrument cable for the SK 9000 bodypack transmitter
- B 60/B 61 battery packs
- BA 60/BA 61 accupack
- L 60 charger
- Product overview
- EM 9046 receiver
- Antennas and antenna boosters
- GZL 9000 antenna cable
- SKM 9000/SKM 9000 COM radio microphone
- SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- BA 60 accupack
- BA 61 accupack
- B 60 battery pack
- B 61 battery pack
- L 60 charger
- Preparing the EM 9046 receiver for use
- Preparing the A/AB/AD 9000 antennas and/or antenna boosters for use
- Preparing the SKM 9000 radio microphone for use
- Preparing the SK 9000 bodypack transmitter for use
- Preparing the L 60 charger for use
- Cascading several chargers
- Setting up or mounting the charger
- Preparing the Digital 9000 system for use
- Using the EM 9046
- Using the SKM 9000
- Using the SK 9000
- Using the L 60
- Cleaning and maintaining the Digital 9000 system
- If a problem occurs ...
- Specifications
Digital 9000 | 67
Using the EM 9046
“
Screensaver”
The “Screensaver” menu item adjusts the “Brightness” to the lowest
(menu-selectable) value, independent of the user-set “Brightness” value.
The “Screensaver” is activated after 30 minutes if the following conditions
are met:
•The “Screensaver” menu item is set to ON.
• No entry via button or jog dial for 30 minutes.
• No RXD card connected to a transmitter for 30 minutes.
The described “Screensaver” state is deactivated and the 30 minutes timer
is restarted if:
• a button is pressed (the function of the button is also performed)
• the jog dial is turned or pressed (the function of the jog dial is also per-
formed)
• the Standby button 3 is pressed
•
a tr
ansmitter is switched on and its signal is received by an RXD card.
The timer remains deactivated as long as the RXD card is connected to
the transmitter
• an error message is displayed over the whole screen. The timer remains
deactivated until the error message is confirmed and is quit using the
esc button L
The described screensaver state remains unchanged if:
• the headphone volume control is turned, i.e. the “Screensaver” remains
active and the screen will not brighten since the headphone volume
control is considered a pure volume control not related to the screen
The “Screensaver” timer is inactive as long as one of the following condi-
tions is met:
•The “Screensaver” menu item is set to OFF.
• An RXD card is connected to a transmitter.
• An error message is displayed over the whole screen.
Extended menu “Service setup”
To get into the extended menu “Service setup”:
왘 In “sys” operating mode, turn the jog dial until “Service setup” appears.
왘 Press the jog dial.
The extended menu “Service setup” appears.
To change from the extended menu back to the main menu:
왘 Turn the jog dial until “System setup” appears.
왘 Press the jog dial.
You are back to the main menu “System setup” of the “sys” operating
mode.