Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
9
Product overviews
Displays and icons on the receiver's display panel
Standard display The standard display appears automatically after switch-on or when no but-
ton has been pressed on the receiver for a long period of time. The brightness
of the standard display automatically dims after a few minutes.
NAME
EQ
DE-S AGC
10 h
15
07
6
B
4
9
8
23
A
1 Equalizer If one of the equalizer functions is activated, EQ appears in inverse on the
standard display (for details, see page 32).
2 De-esser If one of the de-esser functions is activated, DE-S appears in inverse on the
standard display (for details, see page 33).
3 Auto gain control If one of the compression functions is activated, AGC appears in inverse on the
standard display (for details, see page 33).
4 MUTE The received transmitter is not muted, but can be muted at any time (for
details, see page 28).
The received transmitter is muted. In addition, the status LED lights up yellow.
The received transmitter cannot be muted because its MUTE switch is deacti-
vated (for details see page 35).
5 Audio level display The audio level is automatically optimally adjusted.
6 Extended standard display The extended standard display appears when you turn the jog dial to the left
(see page 10). The above shown standard display appears again after 10 sec-
onds or when you turn the jog dial to the right.
7 6-segment RF signal level display Displays the field strength of the received signal. The 6-segment RF signal
level display is also shown on the transmitter display panel.
8 RF output power of the receiver‘s
back channel
Medium RF output
power
Displayed by the -H and -NH10 country variants.
High RF output power Only displayed by the -NH country variant.
9 Lock mode Open padlock icon: The lock mode is temporarily deactivated and the receiver
can be operated as usual.
Locked padlock icon: The lock mode is activated. Press and hold the jog dial to
temporarily deactivate the lock mode. To permanently deactivate the lock
mode, see page 34.
If no padlock icon is displayed, the lock mode is permanently deactivated (for
details, see page 34).
0 Name of the radio link To change this name, see page 32.
A Remaining battery life of the received
transmitter
This information is only displayed when the transmitter is powered via the
optional accupack (for details, see page 27).
B 7-segment display of the transmitter‘s
battery or accupack capacity
The 7-segment battery or accupack capacity display is also shown on the
transmitter display panel (for details, see page 27).