Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
22
Putting the products into operation
Putting the bodypack transmitter into operation
Removing/inserting the batteries or the optional accupack
You can power the bodypack transmitter with the supplied B 30 battery box
and two 1.5 V AA size batteries.
If you use the supplied B 30 battery box to power the bodypack transmitter:
왘 Insert the batteries into the B 30 battery box.
Please observe correct polarity when inserting the batteries.
To remove the battery box or the accupack:
왘 Simultaneously press the two catches and pull the battery box or the accu-
pack away from the bodypack transmitter.
To insert the battery box or the accupack:
왘 Slide the battery box or the accupack onto the bodypack transmitter as
shown.
The battery box or the accupack locks into place with an audible click.
Attaching the bodypack transmitter to clothing
You can use the belt clip to attach the bodypack transmitter to clothing (e.g.
belt, waistband).
Connecting the clip-on microphone or the headset microphone to the
bodypack transmitter
Only connect the clip-on microphone or the headset microphone recom-
mended by Sennheiser. These microphones are optimized for the bodypack
transmitter.
왘 Connect the jack plug of the clip-on microphone or the headset microphone
to the 3.5 mm jack socket (Mic/Line) of the bodypack transmitter.
왘 Lock the jack plug by screwing down the coupling ring.
Optionally, you can also use the Sennheiser BA 30 accupack (3.6 V). The
accupack must be charged before first time use. The accupack can
remain in the bodypack transmitter for charging.