Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
31
Using the products
Level 1 Level 2 To ... See …
Audio
Settings
Low Cut filter out low-frequency noise page 32
Equalizer select a sound profile or manually
adjust the equalizer
page 32
De-Esser attenuate sibilants page 33
Auto Gain
Control
activate/deactivate the dynamic com-
pression
page 33
Effects Reset reset all audio settings to the factory
default settings
page 33
Audio Level fine-tune the receiver‘s output level page 34
Output Type adjust the receiver‘s output level to
match the input (mic or line) of the
connected device
page 34
Exit exit Level 2 and return to Level 1
System
Settings
Auto Lock activate/deactivate the automatic lock
mode
page 34
Mute Switch activates/deactivate the transmitter‘s
MUTE switch
page 35
Display
Brightness
change the brightness of the display
panel
page 35
Help display the QR codes for the help
functions
page 35
System Info display the firmware version and serial
number
page 36
Factory Reset reset the receiver to the factory default
settings
page 36
Exit exit Level 2 and return to Level 1
Network
Settings
Mode change the IP address assignment
mode
page 36
IP change the IP address page 36
Subnet change the subnet mask page 36
Gateway change the gateway address page 37
IPv6 display the IPv6 address page 37
MAC display the MAC address page 37
Exit exit Level 2 and return to Level 1
Name – change the name of the radio link page 32
Walk
Test
– check the reception quality within the
operating environment
page 37
Exit – exit the operating menu and return to
the standard display