Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
39
Using the products
왘 Use a dual-band WiFi router and deactivate its 2.4 GHz frequency band in
order to minimize interference to the radio links.
왘 Connect your mobile devices to the WiFi network and install the “Wireless
System Remote” (WSR) app.
All functions that can be performed directly from the receiver can also be
controlled via the app.
Performing firmware updates
You can either use the “Wireless System Remote” (WSR) app or the
“Sennheiser D1 SL Updater” software to update the firmware. Both the app
and the software can be downloaded free of charge.
The app and the software automatically detect all receivers in the network,
read their firmware version and offer to update the firmware if a newer ver-
sion is available.
Preparing the firmware update 왘 Make sure that all receivers are connected in a network as described on
page 20 and that all receivers are switched on.
왘 Switch off all transmitters.
You first update the firmware of the receivers via the network. Then you
update the firmware of the transmitters via the radio links.
Updating the receiver firmware using
the “WSR” app
To update the firmware using the “WSR” app:
왘 Make sure that your mobile device has Internet access so that you can
download the firmware file.
왘 Start the app.
When started, the app automatically checks for newer firmware.
When started, the “WSR” app automatically checks for newer firm-
ware. You can update both the receiver firmware and the transmitter
firmware (see next chapter).
ATTENTION
Breakdown of radio links during the firmware update
All radio links are subject to interference during the firmware update process
and can therefore not be used for audio transmission.
왘 Never update the firmware during a performance.
왘 Never update the firmware of several transmitters simultaneously.
Breakdown of multi-channel systems due to different firmware versions
All transmitters and receivers of a multi-channel system must run the same
firmware version.
왘 Always update all your transmitters and receivers to the latest firmware
version available.
You can also display the current firmware version of a receiver via the
System Info menu item – without the need for the “WSR” app or the
“Sennheiser D1 SL Updater” software.