Instruction manual 300 IEM Series G3 Download300 IEM Series: SR 300 IEM G3 and EK 300 IEM G3
Table Of Contents
- Important safety instructions
- The evolution wireless series ew 300 IEM G3
- The frequency bank system
- Product overviews
- Putting the devices into operation
- Putting the SR 300 IEM G3 transmitter into operation
- Setting up the transmitter on a flat surface
- Mounting the transmitter into a 19” rack
- Connecting the mains unit
- Connecting devices to the input sockets
- Connecting devices to the output sockets
- Connecting a remote antenna to the BNC socket and positioning the antenna
- Connecting the AC 3 antenna combiner to the BNC socket
- Daisy chaining audio signals
- Connecting transmitters in a network
- Putting the EK 300 IEM G3 diversity receiver into operation
- Putting the SR 300 IEM G3 transmitter into operation
- Using the devices
- Switching the devices on/off
- Monitoring the audio signal via headphones
- Deactivating the lock mode temporarily
- Selecting a standard display on the diversity receiver
- Adjusting the audio channels on the transmitter
- Activating/deactivating the RF signal on the transmitter
- Synchronizing transmitters and EK 300 IEM G3 receivers via the infra-red interface
- Using the operating menus
- Synchronizing the transmitter with the diversity receiver
- Cleaning the devices
- If a problem occurs ...
- Specifications
- Manufacturer Declarations
Using the operating menus
24
Overview of the operating menus
Operating menu of the SR 300 IEM G3 transmitter
When the standard display is shown on the display panel, you can get into the main menu by pressing the jog dial.
The extended menu “Advanced Menu” and the other menus can be accessed via the corresponding menu items.
For more detailed information on the operating menus, refer to the instruction manuals of the transmitter and
the diversity receiver which can be downloaded from www.sennheiser.com.
Display Function of the menu item
Main menu “Menu”
Sensitivity Adjusts the input sensitivity (0 to –42 dB, adjustable in steps of 3 dB)
Mode Selects mono or stereo operation (see page 19)
Easy Setup Deactivates the RF signal and activates Easy Setup Sync (see page 27)
Frequency Preset Sets the frequency bank and the channel
Name Enters a freely selectable name
AutoLock Activates/deactivates the automatic lock mode
Advanced Calls up the extended menu “Advanced Menu”
Exit Exits the operating menu and returns to the standard display
Extended menu “Advanced Menu”
Tune Sets the transmission frequencies for the frequency banks “U1” to “U6”
Sets the channel and the transmission frequency for the frequency banks “U1” to “U6”:
왘 Select this menu item and call it up by pressing the jog dial until the channel selection
appears.
Sync Settings Adjusts the receiver parameters and activates/deactivates their transfer to the EK 300 IEM G3
receiver. For an overview of the parameters, refer to page 20.
RF Power Adjusts the transmission power (“Low” or “Standard”)
Warnings Calls up “Warnings”
LCD Contrast Adjusts the contrast of the display panel in 16 steps
Sensitivity
Easy Setup
Mode
Frequency Preset
Name
AutoLock
Advanced
Exit
Main menu
“Menu”
Tune
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
Extended menu
“Advanced Menu”
AF Peak
RF Mute
Exit
“Warnings”
Balance
Squelch
Mode
High Boost
Auto Lock
Limiter
Exit
“Sync Settings”
Main menu
“Menu”
Squelch
Easy Setup
Frequency Preset
Name
Balance
Mode
High Boost
Auto Lock
Advanced
Exit
Tune
Pilot Tone
Limiter
LCD Contrast
Reset
Software Revision
Exit
Extended menu
“Advanced Menu”
Reset List
Current List
Scan New List
“Easy Setup”
SR 300 IEM G3 transmitter EK 300 IEM G3 receiver