Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
12
Product overviews
Operating elements of the SK D1 bodypack transmitter
1
2
3
4
5
8
9
6
7
7
1 ON/OFF button Short-press to switch the bodypack transmitter on.
Long-press to switch the bodypack transmitter off (for details, see page 26).
2 3.5 mm jack socket
Mic/Line
for connecting the clip-on or headset microphone
3 Status LED
lights up green:
A radio link to the receiver is established. The batteries of the bodypack trans-
mitter are sufficiently charged.
flashes green:
The PAIR button has been short-pressed. Paired devices are being identified
(for details, see page 29).
flashes alternately
green and red:
The PAIR button has been long-pressed. The bodypack transmitter establishes
a radio link to a receiver whose PAIR button has also been long-pressed (for
details, see page 28).
lights up yellow:
The bodypack transmitter has been muted with the MUTE switch. In addition,
Muted is displayed on the display panel (for details, see page 28).
flashes red:
The battery capacity of the bodypack transmitter is only sufficient for approx.
30 minutes of operation.
lights up red:
No radio link to a receiver. In addition, No Link is displayed on the display
panel.
4 MUTE switch for muting the bodypack transmitter (for details, see page 28)
5 Antenna Do not touch the antenna during transmission to avoid a reduction in
the transmission range.
6 Display panel For details, see page 13.
7 Catches Press simultaneously to release the battery box or the accupack.
8 PAIR button Short-press to identify the paired receiver (see page 29).
Long-press to change the pairing (see page 28).
9 Belt clip For details, see page 22.