Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
17
Putting the products into operation
왘 Connect the supplied 2G4 rod antennas to the two R-SMA sockets at the
rear of the receiver.
왘 Align the 2G4 rod antennas vertically upwards.
Mounting the receiver into a 19" rack
For mounting one or several receiver into a rack, you require the optional GA 4
rack-mount kit. The GA 4 rack-mount kit is supplied with individually pur-
chased receivers and is also available separately as an accessory.
Using the GA 4 rack-mount kit, you can:
• mount a single receiver into a 19" rack (see page 18),
• mount the two 2G4 rod antennas to the front of the rack (see page 19) or
• mount two receivers side by side into a 19" rack (see page 19).
The GA 4 rack-mount kit consists of:
When rack-mounting the receiver, you should use the GA 4 rack-mount
kit to mount the receiver antennas to the front of the rack (see next
chapter).
ATTENTION
Danger due to high temperature, mechanical loading or electric leakage cur-
rents
When rack-mounted, the receivers can be damaged by overheat or excessive
mechanical loading.
왘 Make sure that the temperature within the rack does not exceed the per-
missible temperature limit specified in the specifications (see page 46).
왘 Make sure that the receivers in the rack are not mechanically loaded.
왘 Make sure that circuits are not overloaded by providing overcurrent protec-
tion, if necessary.
왘 Make sure that the sum of the leakage currents of all power supply units do
not exceed the allowable limit values by grounding the rack via an addi-
tional ground connection, if necessary.
Do not fit the device feet when mounting the receiver into a 19" rack.
1
3
4
6
5
7
8
9
2