Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
28
Using the products
Muting the bodypack transmitter or the
SKM-S D1 handheld transmitter
Both the bodypack transmitter and the SKM-S D1 handheld transmitter have
a MUTE switch that mutes the audio signal without switching the transmitter
off.
왘 Slide the MUTE switch to the position MUTE.
Muted appears on the display panel of both the transmitter and the
paired receiver. The status LED on both the transmitter and the paired
receiver lights up yellow.
왘 Slide the MUTE switch back to the initial position to unmute the audio sig-
nal.
Pairing a receiver with a transmitter
To establish a new radio link between a receiver and a transmitter, proceed as
follows:
왘 Switch on the receiver and the transmitter that you want to pair (see
page 26).
The status LED on both the receiver and the transmitter indicates the cur-
rent device status (see page 8).
왘 Long-press the PAIR button of the receiver until its status LED flashes alter-
nately green and red.
Identify appears on the display panel of the receiver, followed by the mes-
sage Pairing. An existing radio link is now disconnected. You now have
90 seconds to establish a radio link with a new transmitter.
왘 Long-press the PAIR button of the transmitter until its status LED flashes
alternately green and red.
Press pair on receiver appears on the transmitter display panel.
왘 Wait for approx. 10 seconds until the radio link is established.
- Once the radio link is successfully established, Paired appears on the
display panel of both the receiver and the transmitter and the status LED
on the transmitter and the receiver lights up green.
- If no radio link can be established, Pairing failed appears on the dis-
play panel of both the receiver and the transmitter and the status LED on
the transmitter and/or the receiver lights up red.
- If you try to pair devices that are running incompatible firmware ver-
sions, a message appears on the display panel prompting you to update
the firmware of the transmitter. If you update the firmware now, the
transmitter and the receiver will be paired afterwards; if you do not
update the firmware, the transmitter and the receiver will not be paired
and FW mismatch appears on the display panel of the receiver.
In order that a transmitter can be muted, its MUTE switch must be acti-
vated (see page 35). If you try to mute a transmitter whose MUTE
switch is deactivated, Mute disabled appears on the display panel of
both the transmitter and the receiver.
The SKM D1 handheld transmitter has no MUTE switch and can there-
fore not be muted.
The receiver and the transmitter of a set are factory pre-paired and
therefore ready for immediate use. The radio link is automatically
established as soon as both devices are switched on. You can discon-
nect the existing radio link and establish new radio links to two other
devices.