Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
34
Using the products
Coarsely adjusting the output level of the receiver (Mic/Line)
You can coarsely adjust the output level of the receiver to match the input
(mic or line) of the connected mixing console.
왘 Select Audio Settings – Output Type.
Fine-tuning the output level of the receiver
You can fine-tune the output level of the receiver to match the input (mic or
line) of the connected mixing console.
왘 Select Audio Settings – Audio Level.
왘 Turn the jog dial to increase or reduce the audio level.
Turning the jog dial by one notch increases or reduces the audio level by
1 dB. You can adjust the audio level between 0 dB and 30 dB.
Activating/deactivating the lock mode
The receiver is delivered with the lock mode deactivated. This is indicated by
the open padlock icon on the standard display as shown on the left.
To activate the lock mode:
왘 Select System Settings – Auto Lock – On.
Stored appears on the display panel. The open padlock icon appears
on the standard display for 10 seconds. If, during these 10 seconds, no but-
ton is actuated on the receiver, the lock mode is activated and the locked
padlock icon appears on the standard display.
The lock mode prevents that the receiver is accidentally switched off or that
settings are inadvertently changed during operation. If one of the receiver
buttons is actuated while the lock mode is activated, Locked and To
unlock press & hold SET appears on the display panel of the receiver.
To temporarily deactivate the lock mode:
왘 Long-press the jog dial.
Unlocked appears on the display panel.
The open padlock icon appears on the standard display and the lock
mode is deactivated for 10 seconds. If, during these 10 seconds, no button
is actuated on the receiver, the lock mode is automatically activated again.
To permanently deactivate the lock mode:
왘 If the lock mode is temporarily deactivated, select System Settings – Auto
Lock – Off.
Stored appears on the display panel. The lock mode icon no longer
appears on the standard display.
Exit
Effects Reset
Audio Level
Output Type
Low Cut
10 dB
Line
Off
Audio
Setting Meaning
Line The output level is adjusted to match a line input.
Mic The output level is adjusted to match a mic input.
Exit
Auto Gain Control
Effects Reset
Audio Level
Output Type
Off
10 dB
Line
Audio
NAME
EQ
DE-S AGC
10 h
Auto Lock
Mute Switch
Display Brightness
Off
Active
75
D
e
b
ug
M
o
d
e
System
Exit