Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
37
Using the products
Changing the gateway address You can change the gateway of the receiver.
왘 Select Network Settings – Gateway.
왘 Enter the gateway address.
왘 Select Save and confirm by pressing the jog dial.
Displaying the IPv6 address
왘 Select Network Settings – IPv6.
The IPv6 address is displayed, but it cannot be changed.
왘 Press the ESC button to return to the operating menu.
Displaying the MAC address
왘 Select Network Settings – MAC.
The MAC address is displayed, but it cannot be changed.
왘 Press the ESC button to return to the operating menu.
Performing a walk test (checking the reception quality)
The Walk Test menu item allows you to check the reception quality of your
radio links within the operating environment. By performing a walk test, you
can verify the range and coverage of the radio links.
왘 Switch on the transmitters and receivers of all radio links that you want to
use. In addition, switch on all other devices that you want to use in the
operating environment.
왘 Select Walk Test on all receivers that you want to use for the walk test.
The RF signal level display appears on the display panel of both the receiver
and the transmitter.
왘 Walk the operating environment with one or several paired transmitters.
The RF signal level display on the display panel of both the receiver and the
transmitter is continuously updated.
왘 Check the RF signal level display for more detailed information on the
reception quality:
- Good reception quality is indicated by a tick ( ).
- If the tick is missing, reception quality is sufficient.
- If reception quality is or was compromised at any position, this is indi-
cated by a warning triangle ( ). The warning triangle remains displayed
on the display panel even if reception quality improves afterwards.
- If reception fails completely, the background of the display panel changes
back and forth between light and dark and No Link appears on the dis-
play panel.
왘 Press the ESC button on the receiver to end the walk test.
IP
Subnet
Gateway
IPv6 1188:80F3:1388:...
MAC 00:1B:66:7D:56:D3
0.0.0.0.
0.0.0.0.
0.0.0.0.
Network
Exit
Subnet
Gateway
IPv6 1188:80F3:1388:...
MAC 00:1B:66:7D:56:D3
0.0.0.0
0.0.0.0
Network
Gateway
IPv6 1188:80F3:1388:...
MAC 00:1B:66:7D:56:D3
Mode
0.0.0.0
Fixed IP
Network
Exit
WALKTEST
If the result of the walk test is not satisfying, you can take the following
remedial measures:
• If possible, reposition the receivers so that there is always a direct
line of sight between the receiving antennas and the paired trans-
mitter.
• If possible, remove obstacles between the transmitter and the
receiving antennas.
• When rack-mounting receivers, you should mount their SG4 rod
antennas to the front of the rack using the GA 4 rack-mount kit.