Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
46
Specifications
Specifications
System
* The temperature range is influenced by the battery characteristics
EM D1
AF frequency response 20 to 20,000 Hz
Dynamic range > 128 dB (A)
THD (1 kHz) typ. < 0.1 %
Audio sampling 24 bit/48 kHz
Signal-to-noise ratio typ. 109 dB (A)
RF frequency ranges 2,400 to 2,483.5 MHz
Modulation GFSK with back channel
Transmission method TDMA, time diversity, frequency diversity,
fast switching antenna diversity
Latency 3.9 ms
Audio codec aptX® Live
Relative air humidity max. 95 %
Temperature range*
Operation:
Storage:
–10 °C to +55 °C
–20 °C to +70 °C
RF sensitivity < –90 dBm
RF output power
back channel
10 mW/100 mW (country-specific)
Audio output level gain
Mic/line level switch:
XLR, balanced:
Jack, unbalanced/bal-
anced:
–12 dB/0 dB
max +18 dBu
max. +12 dBu/max. +18 dBu
Audio effects
Low cut:
Equalizer:
De-esser:
Automatic Gain Control
(AGC):
at 120 Hz
7-band graphic equalizer
multi-frequency targets
compression/expansion with automatic make-
up gain function
Display OLED
AF connection sockets XLR/¼" (6.3 mm) jack
Antenna sockets 2 x R-SMA
Network socket RJ45
Network protocol Media Control Protocol,
UDP IPv4 (DHCP, Manual)/IPv6
Power supply 12 V DC hollow jack
Current consumption 350 mA
Weight approx. 824 g