S1 DIGITAL Instruction manual
Contents Contents Important safety information .................................................................................. 2 The S1 DIGITAL headset ............................................................................................. 4 Delivery includes ........................................................................................................ 5 Product overview .......................................................................................................
Important safety information Important safety information 왘 Please read this instruction manual carefully and completely before using the product. 왘 Always include this instruction manual when passing the product on to third parties. 왘 This instruction manual is also available on the Internet at www.sennheiser-aviation.com or www.sennheiser.com. Preventing health problems and accidents 왘 Always maintain a distance of at least 3.
Important safety information 왘 Only replace parts of the product whose replacement is described in this instruction manual. All other parts of the product must be replaced by your Sennheiser partner. Information on active and passive noise attenuation The S1 DIGITAL is a headset with digital adaptive noise compensation. As with any complex electronic device, it is possible for the electronics of the headset to fail during operation.
The S1 DIGITAL headset The S1 DIGITAL headset The S1 DIGITAL aviation headset incorporates the latest in digital technology. Featuring NoiseGardTM/digital noise compensation and excellent passive noise attenuation, the headset is currently the only one on the market that provides optimum protection against cockpit noise over the entire frequency range. The S1 DIGITAL has been designed for use in noisy single- and multi-engine propeller aircraft and helicopters.
Delivery includes Delivery includes S1 DIGITAL headset Transport case for headset and accessories Cable clip Wind and pop screen Belt clip S1 DIGITAL Setup | Inbetriebnahme | Mise en service Switching the operating control on/off | Bedienteil ein-/ausschalten | Bedienteil ein-/ausschalten Andruckkraft einstellen | Andruckkraft einstellen | Andruckkraft einstellen Smart-Update nutzen | Smart-Update nutzen | Smart-Update nutzen OFF ON Quick Guide S1 DIGITAL 45° Manual Quick Guide Kurzanleitung
Product overview Product overview Overview of the headset 1 A 8 7 A 2 3 6 4 5 1 Headband padding 2 (Outer) NoiseGardTM/digital microphone 3 Smart Update button 4 Smart Update LED 5 Microphone 6 (Inner) NoiseGardTM/digital microphone 7 Ear pads 8 Contact pressure slide switch Before wearing the headset, remove the protective foil A from the Sennheiser logo.
Product overview Overview of the control unit C D B 9 0 J K A I E F G H M L 9 0 A B C D E F LED Fast-forward button Volume button Rewind button Volume button Multi-function button MUTING OFF/ON switch Mono /stereo switch G H I J K Power OFF/ON switch Power LED Master VOLUME slide control Phone button Hollow jack socket for optional power supply L 5.25 mm jack plug (PJ-068 equivalent) M ¼” (6.
Putting the S1 DIGITAL into operation Putting the S1 DIGITAL into operation Connecting the headset to the intercom 왘 Connect the jack plugs of the control unit M to the corresponding jack sockets of your intercom. L Jack plug of the control unit Jack socket of the intercoms 5.25 mm jack plug L Microphone input ¼” (6.35 mm) jack plug M Headphone output Powering the headset CAUTION Danger of short circuit! Technical defects can cause a short circuit.
Putting the S1 DIGITAL into operation Connection via the cigarette lighter socket The Adapter-P-CIG adapter cable (optional accessory available from your Sennheiser partner) allows you to connect the headset to the on-board DC power supply system (12 – 35 VDC) via the cigarette lighter socket. 왘 Connect the cigarette lighter plug to the on-board DC power supply system. 왘 Connect the hollow jack plug of the adapter cable to the hollow jack socket on the control unit.
Putting the S1 DIGITAL into operation Type of use Type Operating time NoiseGardTM/digital Alkaline batteries/rechargeable batteries approx. 25 hrs Lithium batteries approx. 40 hrs NoiseGardTM/digital and Alkaline batteries/rechargeable Bluetooth technology batteries Lithium batteries approx. 15 hrs approx. 25 hrs If the battery capacity is low, the headset automatically switches off to protect the batteries/rechargeable batteries from total discharge and leakage.
Putting the S1 DIGITAL into operation Attaching the cable clip The cable clip allows you to attach the headphone cable to your clothing so that the cable doesn’t hinder or distract you. 1 Guide the headphone cable through the cable clip. 2 Attach the cable clip to your clothing. 3 Loop the cable through the clip so that the headphone cable doesn‘t hinder you. 1 2 Attaching the design caps Design caps in different finishes and with individual imprints are available from your Sennheiser partner.
Putting the S1 DIGITAL into operation Connecting the headset to a Bluetooth device CAUTION Danger of malfunction due to radio waves! The transmitted radio waves of mobile phones can impair the operation of sensitive and unprotected devices. 왘 Only make calls with the headset in environments where wireless Bluetooth transmission is permitted. The headset complies with the Bluetooth 2.1 standard.
왘 Press and hold the multi-function button until the LED alternately flashes blue and red. 왘 On your audio source, activate the Bluetooth function “Add a new device”. 왘 When the mobile phone prompts for a password or PIN code, enter the default PIN code “0000”. 왘 Proceed as described in the instruction manual of the mobile phone. Once the headset has found the mobile phone, the devices exchange device identification information. The LED flashes 3 times blue. You hear an ascending beep.
Putting the S1 DIGITAL into operation Switching the “Bluetooth connection” flashing on/off To switch the flashing off during an existing Bluetooth connection: 왘 Switch the Bluetooth function off (see page 17). 왘 Press and hold the multi-function button until the LED alternately flashes blue and red. 왘 Briefly press the Volume button. 왘 To make the new setting effective, press and hold the multi-function button until the LED stops flashing.
Using the S1 DIGITAL Using the S1 DIGITAL Individually adjusting the headset and wearing it Adjusting the headband For good noise attenuation and best possible comfort, the headset has to be adjusted to properly fit your head. To do so, you can adjust the headband. 1 Wear the headset so that the headband runs over the top of your head.
Using the S1 DIGITAL Adjusting the contact pressure The S1 DIGITAL allows you to choose your preferred contact pressure setting, which offers a good balance between best possible noise attenuation and still comfortable contact pressure. In order to achieve greater noise attenuation, a higher contact pressure is required. 1 Tilt the ear cups by approx. 45° to release the mechanics of the slide switches. 2 Use the 3-step slide switches to change the contact pressure for each ear cup.
Using the S1 DIGITAL Switching the headset on/off 왘 Set the Power OFF/ON switch to the position ON. ON NoiseGardTM/digital is switched on. The Power LED lights up, indicating the battery charge status or power supply via the on-board DC power supply system. OFF NoiseGardTM/digital is switched off. The Power LED goes off. OFF ON When the S1 DIGITAL, and thus NoiseGardTM/digital, is switched off, it can be used as a conventional, passive headset.
Using the S1 DIGITAL Switching the Bluetooth function off 왘 Press and hold the multi-function button until the LED flashes 3 times red. You hear a descending beep. The Bluetooth function is deactivated. If you switch the Bluetooth function off, NoiseGardTM/digital remains switched on. Adjusting the headset to the listening situation Adjusting the volume WARNING Danger of hearing damage! Listening at high volume levels for long periods can lead to permanent hearing defects.
Using the S1 DIGITAL Switching between mono and stereo mode The control unit features a mono /stereo switch F which allows you to switch between mono and stereo mode, depending on the intercom. 왘 Set the mono /stereo switch F to the desired position: = mono = stereo Using Smart Update The noise level in the cockpit changes depending on the flight situation. Whenever you perceive a change in the noise level (e.g.
Using the S1 DIGITAL Activating the “auto shut-off” function The “auto shut-off” function automatically switches the headset off when it is disconnected from the intercom or when the aircraft avionics are switched off. With the “auto shut-off” function activated, the operating time is increased. The headset is delivered ex-works with the function deactivated. 1 Open the cover of the battery compartment on the control unit. 2 Set the Auto Shut-Off switch to the position ON.
Using the S1 DIGITAL The following switch positions apply to the left and right channel: No treble boost Treble boost – step 1 Treble boost – step 2 Treble boost – step 3 Adjusting the microphone sensitivity The microphone sensitivity has been factory preset to 35 mV/Pa. 왘 Use a slotted screwdriver to adjust the microphone sensitivity.
Using the S1 DIGITAL Remote-controlling connected Bluetooth devices You can directly remote-control any Bluetooth device supporting the AVRCP profile and connected to the S1 DIGITAL by using the buttons on the headset. Please refer to the instruction manual of your audio source for information on whether your Bluetooth device supports the AVRCP profile.
Using the S1 DIGITAL Muting connected Bluetooth devices If the MUTING OFF/ON switch is set to the position ON, any Bluetooth transmission is muted once ATC communications have been established. When the ATC conversation is over, the muting is automatically canceled.
Using the S1 DIGITAL Remote-controlling a mobile phone If your S1 DIGITAL has a Bluetooth connection to your mobile phone, the LED flashes blue when the mobile phone is ringing. You can also hear the ring tone of your mobile phone in the headset if your mobile phone supports this function.
Using the S1 DIGITAL During a call: Button Any button Duration Function 5s Transfers the ongoing call back to the mobile phone 2s Activates the muting function (acknowledgement tone) Deactivates the muting function Resetting the settings of the headsets You can reset all settings of your headset to the factory default settings. In doing so, the connection profiles of the Bluetooth devices used are deleted, thus preventing that other users of the headset can access your Bluetooth enabled devices.
Transporting the S1 DIGITAL Transporting the S1 DIGITAL The headset comes with a transport case. To ensure optimum protection of the headset when not in use or during transport, you should store the headset in the supplied transport case. Folding up the headset For space-saving stowage, e.g. in your pilot’s case, you can fold the headset compactly. 왘 Fold the right ear cup inwards.
Cleaning/maintaining the S1 DIGITAL Cleaning/maintaining the S1 DIGITAL CAUTION Liquids can damage the electronics of the product! Liquids entering the housing of the product can cause a short-circuit and damage the electronics. 왘 Keep all liquids far away from the product. 왘 Do not use any solvents or cleansing agents. 왘 Before cleaning, pull out the plugs of the product from the connections in the aircraft. 왘 Only use a soft, dry cloth to clean the product.
Cleaning/maintaining the S1 DIGITAL Replacing the ear pads 1 Grasp the edge of the ear pad and peel it up and away from the ear cup. 2 Slide the new ear pad onto the ear cup. 1 2 Replacing the wind screen 1 Pull the wind screen from the microphone. 2 Carefully slide the new wind screen over the microphone.
If a problem occurs ... If a problem occurs ... Problem Possible cause Power LED H The batteries/rechargedoes not light able batteries are flat. up on switch-on No audio signal during Bluetooth connection Solution Page Charge the rechargeable batteries or replace the batteries. 9 The aircraft fuse is defective. Check the aircraft fuse. – The headset is switched off. Switch the headset and the Bluetooth function on. 17 The headset is not paired with a Bluetooth device.
Accessories and spare parts If a problem occurs that is not listed in the above table or if the problem cannot be solved with the proposed solutions, please contact your local Sennheiser partner for assistance. To find a Sennheiser partner in your country, search at www.sennheiser-aviation.com > “Purchase Information” or www.sennheiser.com > “Service & Support”. Accessories and spare parts Accessories Cat. No.
Valuable information on NoiseGardTM/digital Valuable information on NoiseGardTM/digital Combination of two NoiseGard strategies Active noise compensation (ANR, NoiseGard) is based on the principle of cancelling out unwanted sound using “anti-sound” (phase-inverted sound). There are two distinct strategies: the feedback (FB) strategy and the feedforward (FF) strategy .
Valuable information on NoiseGardTM/digital e id ts ou e is no FF inside noise anti noise FB Adaptation The NoiseGardTM/digital technology of the S1 DIGITAL uses an innovative approach. The sound captured by the sensing-microphones is analyzed to calculate the optimum control circuit settings. This calculation is carried out by a highperformance signal processor using a fully-adaptive algorithm.
Valuable information on NoiseGardTM/digital When compared with other adaptive technologies that are on the market, the particular strength of the fully-adaptive FF-NoiseGard is its ability to cancel broadband noise and not just individual tonal components. Cockpit noise consists of a mixture of broadband noise components and individual tonal components (e.g. the fundamentals and harmonics of propeller rotation).
Specifications Specifications Headset Transducer principle Ear coupling Frequency response Impedance active/passive Characteristic SPL Max. SPL THD Contact pressure, adjustable Microphone incl.
Specifications Bluetooth Bluetooth Range Transmission frequency Transmission power Profiles Codec version 2.1 + EDR up to 10 m 2.4 GHz – 2.48 GHz 8 dBm HSP, HFP, A2DP, AVRCP SBC Connector assignment 5.25 mm jack plug (PJ-068 equivalent) 1 Not assigned 2 Microphone High 3 Microphone Low ¼” (6.
Manufacturer declarations Manufacturer declarations Warranty Sennheiser electronic GmbH & Co. KG gives a warranty of 5 years on this product. For the current warranty conditions, please visit our website at www.sennheiser-aviation.com or www.sennheiser.com or contact your Sennheiser partner. In compliance with the following requirements • RoHS Directive (2002/95/EC) • WEEE Directive (2002/96/EC) CE Declaration of Conformity • R&TTE Directive (1999/5/EC) The declaration is available at www.sennheiser.com.
Manufacturer declarations Statements regarding FCC and Industry Canada FCC Declaration of Conformity (DoC) SENNHEISER Model No: S1 DIGITAL We, Sennheiser Electronic Corporation One Enterprise Drive • Old Lyme • CT 06371 • USA Tel: +1 (860) 434 9190, ext. 144 Fax: +1 (860) 434 1759 declare the above device comply with the requirements of Federal Communications Commission. This device complies with Part 15 of the FCC rules.
Manufacturer declarations RF Radiation Exposure Information Since the radiated output power of this device is far below the FCC radio frequency exposure limits, it is not subjected to routine RF exposure evaluation as per Section 2.1093 of the FCC rules. This device complies with the US and Industry Canada portable device RF exposure limits set forth for an uncontrolled environment and is safe for intended operation as described in the user manual.
Sennheiser electronic GmbH & Co. KG Bedienungsanleitung Am Labor 1, 30900 Wedemark, Germany Instruction manual Notice d’emploi www.sennheiser-aviation.com | www.sennheiser.com Instrucciones de uso Printed in Germany, Publ.