System instruction manual TeamConnect
Table Of Contents
- Important safety instructions
- Package contents
- How to read this manual
- Using the TeamConnect system
- The TeamConnect components
- TeamConnect Central Unit
- TeamConnect Combox
- Microphone Hub
- SpeechLine microphones and microphone accessories
- SpeechLine active loudspeakers
- Configuration Manager software
- SL TeamConnect CU1 - Product overview
- SL TeamConnect CB1 - Product overview
- SL Mic Hub 1 - Product overview
- Installing the SL TeamConnect CU1
- Establishing a network connection
- Connecting the SL TeamConnect CU1 to the telephone landline network
- Connecting the SL TeamConnect CB1 to the SL TeamConnect CU1
- Installing the SL TeamConnect CB1 in a meeting room
- Using the GPIO port of the SL TeamConnect CB1
- Connecting a computer
- Connecting a headset or an enterprise telephone
- Connecting the SL TeamConnect CU1 to a media control system
- Connecting and positioning microphones
- Connecting microphones using the SL Mic Hub 1
- Connecting microphones directly to the SL TeamConnect CU1
- Connecting auxiliary audio devices
- Connecting audio output signals
- Preparing the Quick Guide and the Room Sticker for the user
- The Configuration Manager software
- Installing the Configuration Manager software
- Connecting a computer for configuring the system
- Navigating the Configuration Manager software
- Configuring the SL TeamConnect CU1
- Configuring microphone settings
- Configuring audio processing settings
- Configuring line input settings
- Configuring audio output settings
- Configuring teleconference settings
- Configuring the settings of the SL TeamConnect CB1
- Configuring communication settings
- Using the Device Toolbox
- Using the Mixer Console
- Using presets
- Specifications
- Manufacturer Declarations
Specifications
68 | TeamConnect
MEB 102-L TC
Transducer principle pre-polarized condenser microphone
Acoustic principle boundary layer microphone
Pick-up pattern omni-directional
Frequency response 40 Hz – 20 kHz
Nominal impedance at 1 kHz 200 Ohm
Sensitivity 16 mV/Pa
Maximum sound pressure level 125 dB
Equivalent noise level 21 dB (A)
Equivalent noise level weighted as per
CCIR 468-3
31 dB (CCIR)
Dynamic range 104 dB (A)
Phantom power P 24 – P 48
Current consumption 6 mA
Connector XLR 5
Pin assignment XLR-5M out
1 = gnd
2 = + (Mic +)
3 = - (Mic -)
4 = LED green (trigger signal)
5 = LED red (default)
LED light ring color red / green
TTL levels for LED activation
high > 2.4 V
low < 0.4 V
Connection cable
XLR-5F / Terminal connector 5-pin,
length 3 m
Weight 58 g
Height 83 mm (12mm above surface)
Diameter 28.5 mm
Thread M 20
Operating temperature 0 ° to +40 °C
MEB 104-L TC
Transducer principle pre-polarized condenser microphone
Acoustic principle boundary layer microphone
Pick-up pattern cardioid
Frequency response 40 Hz – 20 kHz
Nominal impedance at 1 kHz 200 Ohm
Sensitivity 14 mV/Pa
Maximum sound pressure level 125 dB
Equivalent noise level 28 dB (A)
Equivalent noise level weighted as per
CCIR 468-3
38 dB (CCIR)
Dynamic range 97 dB (A)
Phantom power P 24 – P 48
Current consumption 6 mA
Connector XLR 5
Pin assignment XLR-5M out
1 = gnd
2 = + (Mic +)
3 = - (Mic -)
4 = LED green (trigger signal)
5 = LED red (default)
LED light ring color red / green