ZUBEHÖR STUDIO-RICHTMIKROFON MKH 416 T CONDENSER MICROPHONE ACCESSORIES Kurzbeschreibung K 0 N D ENSA TOR -M IKRO FO N- Das Studio-Richtmikrofon MKH 416 T ist ein Kondensator-Mikrofon in Hochfrequenzschaltung. Die zum Betrieb des Mikrofons notwendige Gleichspannung wird über die beiden Tonadern des Anschlußkabels zugeführt (Tonaderspeisung nach DIN 45595). ACCESSOIRES POUR MICROS ELECTROSTATIQUES Windschutz MZW 415 Windshield MZW 415 Bonnette anti-vent MZW 415 " . . (Art.-Nr ",.
Richtdiagramm 900 900 1800 1800 250Hz 500Hz 1000Hz 2000Hz 4000Hz """" . . '" 8ooo Hz Frequenzkurve --j-- r= r= 110dB _mt- f- _- t-- t" " Sollfrequenzgang '00 """ mit Toleranzschema ,00>0 ,- ,=." MKH 416 T Jedem Mikrofon legen wir das Original-Meßprotokoll von 50 . . . 20000 Hz.
TECHNISCHE HINWEISE sorgt. Es muß aber darauf geachtet werden, daß durch den Aufbau auf Stativen usw. keine mehrfachen Erdungen entstehen. Hochfrequenzscha Itu ng Die Kapsel eines Kondensator-Mikrofons in Hochfrequenzschaltung stellt im Gegensatz zu der in Niederfrequenzschaltung eine niederohmige Impedanz dar. An der Kapsel liegt anstelle der sonst nötigen hohen POlarisationsspannung lediglich eine Hochfrequenzspannung von etwa 10 V, die durch einen rauscharmen Oszillator (8 MHz) erzeLigt wird.
SPEZIAL-ZUBEHÖR FÜR MKH 416 T Windschutz MZW 415 Der Schaumnetz-Windschutz wird bei windgefährdeten Aufnahmen über die Schal1einlaßöffnung des Mikrofons gezogen. Größter Durchmesser: 52 mm, Länge: 210 mm, Dämpfung der Windstörung ca. 15dB. Federhalterung MZS 415 Die Federhalterung kann auf alle Stative, Ausleger usw. mit 3/S"Gewinde aufgeschraubt werden und vermindert Aufnahmestörungen durch Trittschall oder Bodenschwingungen. Durchmesser: 35 mm, Länge: SO mm.
DIRECTIONAL STUDIO MICROPHONE MKH 416 T Polar Diagram Short Description The directional studio microphone MKH 416 T is a transistorized RF condenser microphone. The DC voltage necessary for operation is fed through the conductors of the connecting cable (A-B powering according to the German standard DIN 45595). The MKH 416 T represents a combination of apressure gradient transducer and an interference microphone.
TECHNICAL NOTES High Frequency is being used for professional studio purposes, this is not critical, as the large output voltage of the microphone combined with its low output impedance provides a large signal to noise ratio. Care should be taken, however, that no multiple ground circuits are formed when the.microphones are mounted on tripods etc. Connection to Amplifiers with High Input Sensitivity In the amplifier being used has a very high input sensitivity, i.e.
SPECIAL ACCESSORIES FOR MKH 416 T Power supplies Cables Power unit MZN 16T andT-U Windshield For two 220 The Connecting cable KA 1 and KA 7 Tripie eonductor screened cable. Fitted with 3 pin conneetors according to DIN 41524. KA 1: 1.5 m long KA 7: 7.5.m long. MZW 415 The foam-rubber-windshield should be drawn over the sound inlets of the microphone when wind disturbances are evident.
MICROPHONE DIRECTIONNEL OE STUDIO MKH 416 T Description abregee Diagramme de directivite Le microphone directionnef de studio MKH 416 Test un microphone electrostatique 11haute-frequence. La tension continue necessaire au fonctionnement du micro est amenee par les deux conducteurs de modulation du cable de raccordement (alimentation par conducteurs de modulation selon DIN 45 595). Le MKH 416 Test une combinaison d'un capteur a gradient de pression et d'un capteur d'interferences.
NOTICES TECHNIQUES Montage haute frequence Contrairement au montage basse frequence, la capsule d'un micro electrostatique a haute frequence presente une faible impedance. A la place de la tension de polarisation relativement elevee, la capsule n'est soumise qu'a une faible tension d'environ 10 volts, fournie par un oscillateur (8 MHz) a faible bruit de fond. La faible impedance du systeme mene a une haute fiabilite des microphones.
r ACCESSOIRES SPECIAUX POUR Alimentations MKH 416 T Alimentation secteur MZN 16T et T-U Pour I'alimentation simultanee de deux microphones. Branchement au secteur 220 V ou 110 V-. Le bloc d'alimentation peut etre intercale en n'importe quel point du cordon du micro. Modele T-U avec connecteurs Cannon. Dimensions en mm: 168 x 120 x 50.
--- - - - - ---- Batterieadapter MZA 15 Battery MZA 15 adapter Adaptateur a piles MZA 15 Batterieadapter MZA 15-U Battery MZA 15-U adapter ~ (Art.-Nr.1012) (Art. No. 1012) (N° rer. 1012) Adaptateur a piles MZA 15-U Netzgerät MZN16 T und T-U Power Unit MZN 16 T and T-U Alimentation secteur MZN 16 T et T-U (Art.-Nr. 1236 und 1237) (Art. No. 1236 and 1237) (N° rer.