Book_524137_1007_Sp6.book Seite 0 Freitag, 9.
Book_524137_1007_Sp6.book Seite 1 Freitag, 9. November 2007 2:22 14 Contents Important safety information ................................................ 2 MKH 800 TWIN ........................................................................... 3 Delivery includes ....................................................................... 4 Putting the microphone into operation ................................ Connecting the microphone .............................................. Aligning the microphone ...
Book_524137_1007_Sp6.book Seite 2 Freitag, 9. November 2007 2:22 14 Important safety information Notes on these instructions for use y Please read these instructions carefully and completely before using the microphone. y Make these instructions easily accessible to all users at all times. y Always include these instructions when passing the microphone on to third parties. During operation y Water entering the housing of the microphone can cause a short-circuit and damage the electronics.
Book_524137_1007_Sp6.book Seite 3 Freitag, 9. November 2007 2:22 14 MKH 800 TWIN The MKH 800 TWIN is a universal studio condenser microphone of exceptional quality. It includes a dual capsule consisting of two symmetrical push-pull transducers with high linearity. This is a “side fire” microphone with the two cardioid pick-up patterns of the transducer aligned back-to-back across the axis of the microphone. The MKH 800 TWIN is based on the MKH 800.
Book_524137_1007_Sp6.book Seite 4 Freitag, 9.
Book_524137_1007_Sp6.book Seite 5 Freitag, 9. November 2007 2:22 14 Putting the microphone into operation Connecting the microphone The MKH 800 TWIN has been designed for a 48 ± 4 V phantom powering according to IEC 61938. To power the microphone: 왘 Connect the XLR-5 socket of the adaptor cable to the XLR-5 connector of the microphone. 왘 Connect the two XLR-3 connectors of the adaptor cable to the corresponding sockets of your mixing console. 왘 Switch on the phantom powering on your mixing console.
Book_524137_1007_Sp6.book Seite 6 Freitag, 9. November 2007 2:22 14 Attaching the windshield Pop noises resulting from close miking can be suppressed effectively using the optional MZW 80-ANT windshield or the optional MZP 40 popperstopper (see “Accessories and spare parts” on page 9). To attach the windshield: 왘 Slide on the windshield onto the sound inlet basket . To attach the popperstopper: 왘 Attach the gooseneck of the popperstopper to the stand. The popperstopper changes the sound only slightly.
Book_524137_1007_Sp6.book Seite 7 Freitag, 9. November 2007 2:22 14 Pick-up pattern Setting Figure-8 왘 Set the amplification to the same value in both channels. 5 5 0 0 -5 -5 왘 Invert the phase of the rear channel. Phase Super-cardioid** 왘 Set the amplification in the rear channel lower than in the front channel. 5 5 0 0 -5 -5 - 10 - 10 - 15 - 30 - 15 - 30 왘 Invert the phase of the rear channel.
Book_524137_1007_Sp6.book Seite 8 Freitag, 9. November 2007 2:22 14 Changing the pick-up pattern There are two different ways of changing the pick-up pattern of the microphone. If the microphone level has to be changed infrequently: 왘 At the mixing console, set the preamplification to the same value in both channels. 왘 Vary the pick-up pattern by using the level control and the phase switch of the rear channel. The level control of the front channel stays in the same position.
Book_524137_1007_Sp6.book Seite 9 Freitag, 9. November 2007 2:22 14 Care and maintenance CAUTION! Liquids can damage the microphone! Liquids entering the microphone can cause a short-circuit in the electronics and damage the microphone capsule. 왘 Do not use any solvents or cleansing agents. 왘 Use a soft, slightly damp cloth to clean the microphone from time to time. Accessories and spare parts Cat. No.
Book_524137_1007_Sp6.book Seite 10 Freitag, 9. November 2007 2:22 14 Specifications Short description Dual diaphragm RF condenser microphone with separate outputs for both capsules Pick-up pattern 2 x cardioid Frequency response 30–50,000 Hz Sensitivity (no load) at 1000 Hz 40 mV/Pa (–28 dBV) ±1 dB Output impedance at 1000 Hz 100 Ω Max. SPL at 1000 Hz 134 dB (100 Pa) Max. output voltage 4V Min.
Book_524137_1007_Sp6.book Seite 11 Freitag, 9. November 2007 2:22 14 Polar diagram and frequency response curve Polar diagram 0° 0 30° 30° 5 10 60° 60° 15 20 25 90° 90° dB 120° 120° 125 Hz 4000 Hz 250 Hz 150° 500 Hz 150° 180° 1000 Hz 8000 Hz 16000 Hz 32000 Hz 2000 Hz The polar diagrams of both channels only differ in the opposite alignment 0°/180°.
Book_524137_1007_Sp6.book Seite 12 Freitag, 9. November 2007 2:22 14 Manufacturer Declarations Warranty 2 years CE Declaration of Conformity Sennheiser electronic GmbH & Co. KG declare that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. The declaration is available on the internet site at www.sennheiser.com.
Book_524137_1007_Sp6.book Seite 0 Freitag, 9. November 2007 2:22 14 Sennheiser electronic GmbH & Co. KG Am Labor 1 30900 Wedemark, Germany Phone +49 (5130) 600 0 Fax +49 (5130) 600 300 www.sennheiser.com Printed in Germany Publ.