Instruction manual ew D1
Table Of Contents
- Contents
- Important safety instructions
- Optimum sound the easy way
- Package contents
- Product overviews
- Putting the products into operation
- Avoiding sources of interference
- Direct line of sight recommended
- Putting the receiver into operation
- Fitting the device feet
- Mounting the rack mount “ears”
- Connecting the rod antennas to the receiver
- Mounting the receiver into a 19" rack
- Mounting a single receiver into a rack
- Mounting the rod antennas to the front of the rack
- Mounting two receivers into a rack
- Connecting the receiver to a mixing console
- Connecting receivers in a network
- Connecting the receiver to the power supply system
- Putting the bodypack transmitter into operation
- Preparing the headset microphone for use
- Attaching the clip-on microphone to clothing
- Putting the handheld transmitter into operation
- Recharging the accupack
- Using the products
- Switching the devices on or off
- Checking the charge status of the batteries or accupacks
- Checking the RF signal level
- Muting the bodypack transmitter or the SKM-S D1 handheld transmitter
- Pairing a receiver with a transmitter
- Identifying paired devices
- Using the devices in multi-channel operation
- Switching between the standard display and the extended standard display
- Using the operating menu of the receiver
- Using the buttons for navigation
- Overview of the operating menu of the receiver
- Changing the name of the radio link
- Activating/deactivating the low-cut filter
- Adjusting the equalizer
- Adjusting the de-esser
- Activating/deactivating the dynamic compression
- Resetting the audio settings
- Coarsely adjusting the output level of the receiver (Mic/Line)
- Fine-tuning the output level of the receiver
- Activating/deactivating the lock mode
- Activating/deactivating the MUTE switch of the transmitter
- Adjusting the display brightness
- Calling up help functions
- Retrieving system information
- Resetting the receiver to the factory default settings
- Changing the network configuration
- Displaying the IPv6 address
- Displaying the MAC address
- Performing a walk test (checking the reception quality)
- Controlling, monitoring or updating devices via the network
- Cleaning and maintaining the products
- If a problem occurs ...
- Specifications
- Accessories
- Manufacturer Declarations
32
Using the products
Changing the name of the radio link
You can change the name of the radio link. This name is displayed on the dis-
play panels of the paired devices.
왘 Select Name.
왘 Select and confirm the character that you want to change. Then select the
new character.
You can enter up to 8 capital letters from A to Z and digits from 0 to 9.
To delete the selected character:
왘 Select DEL and confirm by pressing the jog dial.
To store the entered name:
왘 Select SAVE and confirm by pressing the jog dial.
Activating/deactivating the low-cut filter
You can filter out low-frequency noise caused, for example, by the proximity
effect of the microphone or by wind.
왘 Select Audio Settings – Low Cut.
Adjusting the equalizer
You can adjust a sound profile to e.g. improve speech intelligibility or adjust
the sound to the room acoustics.
왘 Select Audio Settings – Equalizer.
You can select an existing sound profile or manually adjust the equalizer.
To select an existing sound profile:
왘 Select the desired sound profile.
If one of the equalizer functions is activated, EQ appears in inverse on the
standard display.
To manually adjust the equalizer:
왘 Select Custom.
The equalizer is displayed.
DEL SAVE
Name
F
G
HANDHELD
I
J
Low Cut
Equalizer
De
-
Esser
On
Off
Off
O
u
t
pu
t
T
ype
Audio
Exit
Setting Meaning
On The low-cut filter is activated. Low-frequency noise is fil-
tered out.
This setting is recommended if you mainly want to transmit
speech.
Off The low-cut filter is deactivated. Low-frequency noise is not
filtered out.
This setting is recommended if you want to transmit music
or sound effects with a dominant bass component.
Equalizer
De-Esser
Auto Gain Control
On
Off
Off
Low Cut
Audio
Exit