User's Manual

Strips MS-H Article # 1302002
Strips MS-WL Article # 1301002
User Manual
11.
PRODUCT /WARRANTY/WARRANTY PERIOD/DEFECT:
Sensative AB (”Company”) warrants to the original end-user purchaser (“Purchaser”)
that Strips (“Product”) will be free from substantial defects in material and workmanship
from the date when the Product is delivered to the Purchaser and continues for twelve
(12) months thereafter (“Warranty period”). The information contained herein is provided
to the Purchaser as a convenience.
LIMITATION OF PRODUCT WARRANTY:
Company warrants that the Product under normal use is free from substantial defects
in material and workmanship (“Defect”) during the Warranty Period, subject to a proper
installation, operation and maintenance of the Product as set forth in the user manual
and other documentation that may become available to the Purchaser from time to
time at www.sensative.com/strips_tips (“User Manual”). Company does however not
warrant that the Product will operate uninterrupted or error-free or that all deficiencies,
errors, defects or non-conformities will be corrected.
The Warranty extends only to Purchaser and is not transferable to anyone else.
CLAIMS PROCEDURE:
Warranty claims are handled at www.sensative.com/Strips_tips.
Note that warranty claims must be filed to the Company by the Purchaser within 30
days of the manifestation of the problem.
EXCLUSIONS:
The warranty shall not apply to problems or damages resulting from or related
to
i) mechanical and/or transport problems
ii) external causes such as accidents, acts of God, disasters, weather conditions,
air pollution, abuse, misuse, misapplication or any equipment that generates
electrical disturbance of radio communication that violates FCC regulations
iii) negligence, improper handling and failure to operate the Product according
to the User Manual
iv) operating and storage problems
v) electrical power and telecommunications
vi) the network and/or other products in the network
vii) change of window/door position
viii) accessories or attachments not recommended by Company or modifications
to the Product or its parts
ix) failure to follow Companys instructions relating to the Product´s use or
installation and/or to fulfil the maintenance and servicing activities defined in
the User Manual.
INDUSTRY CANADA STATEMENTS:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with the safety requirements for RF exposure in accordance
with RSS-102 §2.5.2. This equipment must be installed and operated in accordance with
the provided instructions and a minimum 20 cm spacing must be provided between the
antenna and any person’s body during wireless modes of operation.
INDUSTRY CANADA NOTICE:
“This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device”
INDUSTRY CANADA STATEMENTS:
Cet appareil est conforme avec Industrie Canada exempt de licence Rss standard(s).
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne
peut causer d’interférences, et (2) cet appareil doit accepter toute interférence, y
compris des interférences qui peuvent provoquer un fonctionnement indésirable du
périphérique.
Ce dispositife est conforme à la norme de sécurité en matière d’exposition RF
conformément à la RSS-102 §2.5.2. Ce dispositif doit être installé et utilisé
conformément aux instructions fournies et à 20 cm espacement minimal doit être
prévu entre l’antenne et le corps de toute personne pendant les modes sans fil de
fonctionnement.
FCC NOTICE (for USA):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
No changes shall be made to the equipment without the Company’s permission as this
may void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limit for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.