Datasheet

ManualsBrandsSensComp ManualsSensorsUltrasonic Transductor 150mm 10.7m

For more information, visit www.senscomp.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. SEE

DISCLAIMER NOTICE AT THE END OF THIS DOCUMENT.

Description

SensComp, Inc.

36704 Commerce Rd.

Livonia, MI 48150 USA

Telephone: (734) 953-4783

Fax: (734) 953-4518

www.senscomp.com

SensComp's totally integrated Series 600 Smart Sensor simplifies product design and packaging.

Features:

50 KHz Electrostatic Ultrasonic sensor

Integrated SMT Drive Electronics

TTL Compatible

Convenient Pin Terminal Connection

Monostable and Astable Modes of Operation

Voltage Regulated

Beam Angle of 15° at -6 dB

Low Ring Characteristics

Ranges from 6” to 35’

Excellent Receive Sensitivity

Available with all Series 600 Ultrasonic sensors

Specifically intended for operation in air at ultrasonic

Frequencies

*PID# 615088LF – Instrument Grade Smart Sensor

*PID# 615089LF – Environmental Grade Smart Sensor

*PID# 615090LF – Open Face Smart Sensor

*PID# 615095LF – Environmental Grade Smart Sensor

w/Parylene

*RoHS Compliant

Self-Contained Compact Design

Easy to Interface with Minimum of External Components

Can be Triggered Internally or Externally

Will Operate on a Power Source from 6 to 24 VDC

Level Measurement, Proximity Detection, Presence Detection,

Robotics, Educational Products

The new SensComp Smart Sensor is based on the ultra-sensitive

Series 600 Electrostatic Ultrasonic sensor line with an enhanced

version of our 6500 ranging module on board. The new voltage

regulated circuitry allows the sensor to operate from a 6 to 24

VDC power source.

The TTL compatible open collector outputs include pull-up

resistors. Configuration of the new oscillator circuit enables the

unit to be externally triggered or continually sense at 5 Hz.

The digitally controlled gain and variable bandwidth amplifier

minimizes noise and side lobe detection in sonar applications.

The typical absolute accuracy is ±1% of the reading over the

entire range.

This new compact integrated design of SensComp’s Series 600

Smart Sensor will expedite the product development process.

Features

Part No.

Benefits

Smart Senso

Specifications

Applications

Smart Sensor

(CLK)

Programmable Jumpe

OSC

ECHO

6-24 VDC

GND

BINH

INIT

BLNK

Gain

Adjust

(VR1)

Summary of content (5 pages)

PAGE 1
SensComp, Inc. 36704 Commerce Rd. Livonia, MI 48150 USA Telephone: (734) 953-4783 Fax: (734) 953-4518 www.senscomp.com Smart Sensor SensComp's totally integrated Series 600 Smart Sensor simplifies product design and packaging.
PAGE 2
Smart Sensor Series 600 Smart Sensor Specifications Distance Range ...................................... 0.15 to 10.7 M (0.5 to 35 Ft) Accuracy (over entire range) .................. ± 0.1% Beam Pattern .......................................... See Graph Typically 15° nominal. Repetition Rate (astable) ........................ 5 Hz May be externally triggered Outputs ................................................... 2 + (INIT) Internal Pull-up resistors to +5 VDC Inputs (TTL Compatible) ...............
PAGE 3
Smart Sensor Electrical Characteristics over Recommended Ranges of Supply Voltage and Operating Free-Air Temperature PARAMETER TEST COND.
PAGE 4
Smart Sensor FIGURE 1: EXAMPLE OF A SINGLE-ECHO-MODE CYCLE WITHOUT BLANKING INPUT Multiple Echo Mode The Series 600 Smart Sensor has an external blanking input, BLNK, enabling selective echo exclusion for operation in a multiple echo mode and can differentiate echoes from objects that are only three inches apart. If there is more than one target and a single transmission detects multiple echoes, then the cycle is slightly different (Figure 2).
PAGE 5
SENSCOMP PRODUCT SPECIFICATION SHEET DISCLAIMER NOTICE SensComp, Inc. (“SensComp”) reserves the right to make corrections, enhancements, improvements and other changes to its products, specification sheets and data, and to discontinue any product, without further notice. Buyer should obtain the latest relevant information before placing an order and should verify that such information is current and complete.