Operating instructions

ManualsBrandsSensormatic ManualsComputer equipmentAD100

Recorder Controller/Interface

Installation Instructions

8000-1828-01, Rev. B SENSORMATIC VIDEO SYSTEMS 1

AD100 Series

Recorder Controller & Multiple

Interface Hookup / Software

Utility Installation & Operating

Instructions

Contents

Video Recorder Control........................................................... 1

Equipment Description............................................................ 2

Drawing 1 – System Equipment.............................................. 3

Initial Hookup.......................................................................... 4

Installing the Software Utility................................................... 4

RIU Programming ................................................................... 4

Drawing 2 – Daisy Chain Configuration................................... 5

Drawing 3 – AD100 Interface w/ PC & Video Recorders ......... 5

Testing Recorder Commands ................................................. 8

Upgrade Kits and Peripherals ................................................. 8

Drawing 4 – AD100 Interface w/ AD1024 System ................... 9

Drawing 5 – AD100 Interface w/ MegaPower 48 System ........ 9

Product Specifications .......................................................... 10

Declaration of Conformity...................................................... 11

If you need assistance…

Contact Technical Support at 1-800-392-2873

(or 845-624-7600). Fax: 845-624-7685

Video Recorder Control

Recorder control hardware and the corresponding utility

software enable an AD1024 or MegaPower 48 system

user to control video recorders at both local and remote

sites. Operators control the video recorders via the

AD2088 keyboard.

Systems developed after AD1024 and MegaPower 48

will also support recorder control. Particular systems

developed before AD1024 can support recorder control

with appropriate upgrade equipment (see the table on

page 8 for details).

The AD Recorder/Controller interface is available for

both 120 VAC and 230 VAC applications.

Equipment Provided

(see Drawing 1, Page 3)

Part Qty Part No.

Recorder Controller (120 VAC) 1 AD100XA

Recorder Controller (230 VAC) 1 AD100XA-1A

IR Interface Module (120 VAC) n AD100IR16

IR Interface Module (230 VAC) n AD100IR16-1A

RL Interface Module (120 VAC) n AD100RL8

RL Interface Module (230 VAC) n AD100RL8-1

RS-232 Interface Module (120 VAC) n AD100RS8

RS-232 Interface Module (230 VAC) n AD100RS8-1

Transformer (120 VAC) n 0650-1772-01

Transformer (230 VAC) ***

n 5604-0180-01

Recorder Interface Utility 1 0701-14Q1-1D4A

Modular Cable 1 6003-0047-02

Adaptor – RJ45 to DB9F 1 2025-0294-01

Adaptor – RJ45 to DB9M 1 2025-0308-01

Velcro Strip n 0500-5689-01

***

The 230 VAC transformer is equipped with a Euro-style IEC

320 type inlet. A suitable, detachable cord should be

connected between the IEC 320 inlet and power source.

The cord should conform to all national and local code

requirements.

Additional Equipment Required

Additional equipment required for the installation of the

recorder controller/interface network includes:

IBM Compatible PC (Windows 95, 98, & NT)

Video Recorder(s)

IR Remote Device(s)

IR Emitter Cable (Part No. AD100IRE)

RS-232 Cable (Part No. AD100RSC)

Resistive Ladder (RL) Cable (Part No. AD100RLW)

Sub-Miniature 3/32” (2.5mm) Phone Plug (plug required

depending on make and model of RL video recorder

used).

Tools Required

Wire Strippers

Small Slotted Screwdriver

Summary of content (12 pages)

PAGE 1
Recorder Controller/Interface Installation Instructions AD100 Series Recorder Controller & Multiple Interface Hookup / Software Utility Installation & Operating Instructions Contents Video Recorder Control........................................................... 1 Equipment Description ............................................................ 2 Drawing 1 – System Equipment .............................................. 3 Initial Hookup ..................................................................
PAGE 2
Equipment Description The following devices and peripherals are available to support integrated switching system and video recorder control (see Drawing 1, page 3 for details). AD100XA Recorder Controller The AD100XA is the central processor of a recorder interface network. A single AD100XA is required for an entire network. The front side of the AD100XA has a DB9F connector for RS232 communication. Note: the connector to the right of the DB9F is not used.
PAGE 3
AD100 Series System Drawings Drawing 1 – System Equipment AD100RS8 Front View AD100RL8 Front View Addressing Switch AD100RS8 Rear View AD100RL8 Rear View Addressing Switch AD100XA Front View AD100IR16 Front View This connector not used Addressing Switch AD100XA Rear View AD100IR16 Rear View IR Receive Sensor AD100RLW Cable AD100RSC Serial Cable AD100IRE Emitter Cable 230 VAC Transformer 120 VAC Transformer Modular Cable with DB9F & DB9M Adaptors for PC to AD100XA Connection Drawing 1 – Syste
PAGE 4
Initial Hookup 4. AD100 series modules can be wall, rack, or desktop mounted using the supplied Velcro strip. Launching the Application On the Windows desktop, click the following sequence: 1. “Start” 2. “Programs” 3. “Sensormatic” 4. “Recorder Installation Utility” The initial window of the RIU software appears: 1. 2. 3. 4. Connect the A and B communications terminals of the AD100XA and all AD100 interface modules in a daisy chain configuration.
PAGE 5
AD100 Series System Drawings Drawing 2 – Daisy Chain Configuration Drawing 2 – Daisy Chain Configuration Drawing 3 – AD100 Interface w/ PC & Video Recorders Drawing 3 – AD100 Interface w/ PC & Video Recorders 8000-1828-01, Rev.
PAGE 6
switch with a non-conductive implement such as the eraser end of a number 2 lead pencil). The dialog box message will change to “Looking for Module 2”. Press the addressing switch on the second interface module. Continue the procedure until all N interface modules have been addressed. Note: With each successive module addressed, additional time is required to find the module. The search time increases by approximately 5 seconds for each additional module.
PAGE 7
. When the transmission is finished, the Recorder In... dialog box appears. Click “OK” to complete the process. Assigning Recorder Types to Outputs Each recorder output must be assigned a recorder type and a recorder number. 1. To assign a recorder type to an output, click on the appropriate selection in the left-most Recorder Types column. The Recorder Library dialog box appears. 2. Press Cancel. 3.
PAGE 8
Testing Recorder Commands Testing IR Commands via PC Prior to final hookup of the AD1024 or MegaPower 48 system with recorder interface hardware, it is advisable to test the IR command set with the system video recorders in a “test bench” setting. This will verify the proper operation of the recorder interface modules while isolating the test from the physical complexities of the actual site installation. Connecting the IR Emitter Cables 1.
PAGE 9
Drawing 4 – AD100 Interface w/ AD1024 System Drawing 4 – AD100 Interface w/ AD1024 System AD100XA AD1024 CPU AD100IR16 AD100RS8 AD2088 Keyboard IR Video Recorders Integra Digital Video Recorder Note: System shown with AD100XA, AD100IR16, and AD100RS8 Modules. AD100RL8 not shown.
PAGE 10
Product Specifications Environmental Specifications Electrical Specifications Operating Temp: 5°C to 40°C(40°F to 104°F) Humidity: 95° non-condensing Storage Temp: -40°C to 70°C (-40°F to 155°F) Power Supply Input Power Source: AD100XA AD100IR16 120 VAC, 60 Hz 120 VAC, 60 Hz AD100XA-1A 230 VAC, 50/60 Hz AD100IR16-1A 230 VAC, 50/60 Hz AD100RL8 120 VAC, 60 Hz AD100RL8-1 230 VAC, 50/60 Hz AD100RS8 120 VAC, 60 Hz AD100RS8-1 230 VAC, 50/60 Hz Power Supply Output Output Voltage: 9-12 VAC @ 0.
PAGE 11
Declaration of Conformity Declaration of Conformity Manufacturer’s Name: Sensormatic Electronics Corporation Manufacturer’s Address: 1 Blue Hill Plaza nd 2 Floor Pearl River, New York, 10965 USA Declares, that the products listed below: Name/Type: AD100 Series Recorder Interface Modules Model Numbers: AD100XA-1A, AD100IR16-1A, AD100RL8-1, AD100RS8-1 comply with all applicable directives as demonstrated by conformance to the following Product Specifications: Safety: EN 60950: 1992 EMC: EN 50130-4
PAGE 12
Sensormatic Video Systems Division 1 Blue Hill Plaza Pearl River, New York, 10965 (845) 624-7600 PN 8000-1828-01, Revision B 12 Recorder Controller/Interface Installation Instructions 8000-1828-01, Rev.