Specifications

ManualsBrandsSensormatic ManualsDigital CameraRHODUL-01

RHODUL OUTDOOR HOUSING INSTALLATION AND SERVICE GUIDE (8000-2830-05, REV. A)

1 of 14

RHODUL

Outdoor Housing

RHODUL-03 with Clear Bubble

RHODUL-04 with Smoked Bubble

Installation and Service Guide

Figure 1

Parts Supplied

· Housing assembly 0100-2468-01

· Bubble assembly 0400-1402-01/-02

· Tamperproof drive (supplied with bubble)

· Install kit 0351-2183-01

Purchase or Supply Separately

· Male BNC connector

Tools Required

· 1/4" fixed-handle nut driver for Torx bit

· Wire cutters and strippers

Contents

About this Guide.....................................................1

About the Outdoor Housing ...................................2

Data Cable Requirements......................................2

Power Cable Requirements ...................................2

Power-Up Routine..................................................2

Synchronizing Domes ............................................2

Warnings and Cautions .........................................3

Procedure ..............................................................5

Troubleshooting Outdoor Domes...........................9

Ordering Parts...................................................... 12

Specifications....................................................... 14

Declarations ......................................................... 14

About this Guide

This guide explains how to install the RHODUL

outdoor housing. It does not explain how to install

the outdoor mounting structure to which the

housing is attached. For this information, see

information shipped with the structure.

Bubble

Assembly

Housing

Assembly

Pigtail

Summary of content (14 pages)

PAGE 1
RHODUL Outdoor Housing Contents RHODUL-03 with Clear Bubble RHODUL-04 with Smoked Bubble Data Cable Requirements......................................2 About this Guide.....................................................1 About the Outdoor Housing ...................................2 Power Cable Requirements ...................................2 Power-Up Routine..................................................2 Installation and Service Guide Synchronizing Domes .......................................
PAGE 2
About the Outdoor Housing Power Cable Requirements The RHODUL outdoor housing (Figure 1) is used to attach the SpeedDome Ultra camera dome to an outdoor mounting structure. Note: This guide assumes that a mounting structure is in place and that data and power cables have been pulled to the installation site. Length of power cable between a Class 2 LPS (low voltage) ac source, such as a J-box, and the dome depends on the ac line voltage.
PAGE 3
Warnings and Cautions ! Please review the following warnings and cautions before you begin installation or service. WARNINGS ! WARNING! ALWAYS USE: · Proper safety equipment for the location and type of installation. · Proper lift equipment to reach the installation. Stromanforderungen in der EU: Dieses Produkt wird mit 24 V Wechselstrom betrieben. In der EU ist es für den Betrieb durch eine begrenzte Stromquelle vorgesehen.
PAGE 4
CAUTIONS The outdoor housing contains an environmental PC board. Touch the metal housing to discharge static electricity before touching this board. Also, use a jeweler’s 2.5mm (0.1") slotted screwdriver to tighten PC board connectors. Wider blade widths can damage connectors. Do not over tighten connectors. You should have two boxes: one for the outdoor housing, the other for the bubble assembly. Protect the bubble assembly by leaving it in its box until you are ready to install it.
PAGE 5
4. Connect data to 6-pin connector on pigtail. Procedure Note: Wire colors are for composite cable only. IMPORTANT! To minimize trips up and down ladder, review procedure first before attempting to attach outdoor housing. Lay out and prepare parts accordingly. Manchester data connections. Order data cable 88760 (plenum) or 8760 (non-plenum) from Belden by calling 1-800-235-3361.
PAGE 6
Setting Line Termination 8. Check LEDs on environmental board to verify power and data are reaching outdoor housing (Figure 3). a. Press and hold switch SW2 and observe green (ac power) and yellow (comm.) LEDs. Green LED glows steadily and yellow LED glows steadily (RS422) or blinks (SensorNet). For a SensorNet/Manchester communication line, jumper JW1 on the environmental board is set at the factory to “terminated” (when communication lines do not continue).
PAGE 7
Attaching the Housing and Eyeball Assembly 2. Set dome address (Figure 6). Recessed at top of housing and eyeball assembly are three rotary address switches. Protocol address ranges are shown below. Set switches from most significant bit (MSB) to least significant bit (LSB). For example: For address 166, set SW3 to 1, SW2 to 6, and SW1 to 6. Perform the following steps on the ground. 1. Remove SpeedDome Ultra housing and eyeball assembly from box and remove BOTH slot covers from eyeball (Figure 5).
PAGE 8
Attaching the Trim Ring/ Bubble Assembly 3. Connect housing and eyeball assembly to the base (Figure 7). a. Align recessed dimple on cap of dome with logo visible on environmental PC board. Refer to Figure 8. b. Mate housing and eyeball assembly to base and turn it clockwise until you hear a click. 1. Remove bubble assembly from package and ensure bubble is clean and free of debris. After a few seconds, dome begins its homing routine and heater fans are on.
PAGE 9
3. Verify data is reaching housing. Troubleshooting Outdoor Domes SENSORNET or RS422: Press and hold switch SW2 on environmental PC board and observe yellow (comm.) LED. Yellow LED should blink (SensorNet) or glow steadily (RS422). For test switch location, see Figure 3. Perform the following procedures if one of the following symptoms occur: - Dome does not respond to commands - Fans do not turn - Picture grainy or discolored - Poor video - Ice forms on bubble.
PAGE 10
Fans Do Not Turn SensorNet Data Connections Pin Color Designation 1-4 — Not used. 5 Brown SensorNet (unshielded) 6 Yellow SensorNet (unshielded) Follow steps until the problem is corrected. See page 12 to order parts. 1. Determine if housing and eyeball assembly is receiving power. Look for evidence such as a picture on the video monitor or dome movement. CAUTION: Screws on connector P1 are delicate. DO NOT over tighten them! Use a 2.5mm (0.1") slotted screwdriver.
PAGE 11
Picture Grainy or Discolored Ice Forms On Bubble Check the fans. If they are not turning, the camera dome may be overheating. See “Dome Does Not Respond to Commands” on page 10. Follow steps until the problem is corrected. See page 12 to order parts. 1. Verify that fans in housing are working. If not, see “Fans Do Not Turn” on page 10. Poor or No Video 2. Determine if housing and eyeball assembly is receiving power. Look for evidence such as a picture on the video monitor or dome movement.
PAGE 12
5. Check heater connector. Is heater connector on other side of environmental PC board plugged into connector P2? Parts list 1 Cable Assy., Fan* 0650-2000-01 2 Heater* 0500-8023-01 3 Lanyard 0500-8797-01 4 Drive, Tamperproof 1400-0149-01 5 Nut, 1-1/2 NPT 6010-0100-01 6 Cover 0500-8001-01 7 Sun Shield 0500-7954-01 8 Nut, M6 (Qty. 4) 5826-0500-020 9 Washer (Qty.
PAGE 13
Figure 9. Outdoor housing assembly (only parts shown in boxes can be ordered) 5 6 7 8 9 10 11 12 13 1 14 15 2 16 17 18 19 21 22 20 3 23 24 4 RHODUL OUTDOOR HOUSING INSTALLATION AND SERVICE GUIDE (8000-2830-05, REV.
PAGE 14
Safety....................................UL1950 CSA C22.2 No. 950 EN60950 IEC 950 Specifications Electrical (combined dome and housing) FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for Class A digital devices when installed and used in accordance with the instruction manual. Following these rules provides reasonable protection against harmful interference from equipment operated in a commercial area.