Installation Guide
Table Of Contents
- Sensys Networks VDS240 Wireless Vehicle Detection System
- Access Point Controller Card (APCC) Installation Guide
- Contents
- Introduction
- Overview
- Access Point Controller Card (APCC)
- Types of APCC Configurations
- APCC Package Contents
- SPP Package Contents
- Additional Parts and Equipment Required
- 1. Cabling – a minimum of one straight-through Ethernet cables are required.
- 2. Laptop PC and TrafficDOT software – if contact closure cards will be configured via TrafficDOT's GUI, a suitable host is required.
- 3. Contact closure card functions can be configured from the switches on the front panel eliminating the need for a laptop PC and TrafficDOT.
- APCC Installation Considerations
- SPP Installation Considerations
- APCC Installation Procedures
- SPP Installation Procedures
- Tools Required for SPP Installation
- Step-by-Step Procedures
- Installing the Mounting Plate on Poles
- Installing the Mounting Plate on Walls
- Installing the Mounting Plate on Beams
- Determining the Type of SPP Radio Bulkhead Connector
- Connecting the Cable to an SPP Radio with the Hex-head Connector
- Step-by-Step Procedures
- Figure 6.6. Remove the factory-installed cap
- Figure 6.7. Inspect the factory-installed gasket
- Figure 6.8. Replace damaged or used gaskets
- Figure 6.9. Thread cable through connector A
- Figure 6.10. Thread cable through connector B
- Figure 6.11. Ethernet cable bushing chart (not to scale)
- Figure 6.12. Fit bushing onto cable between connector A and connector B
- Proper Fit (little to no gap between edges of cut)
- Improper Fit (gap between edges of cut)
- Proper Fit (bushing fully seated into guides)
- Improper Fit (bushing poorly seated into guides)
- Proper Fit (recessed bushing, smooth face)
- Improper Fit (bushing not recessed, pinched edge, mushroomed face)
- Removing the Cable Connection
- Configuration
- Overview
- Configuring Channels With the Front-Panel Interface
- Starting TrafficDOT and Connecting to an APCC
- Configuring Channels with TrafficDOT
- Defining Sensor-to-Channel Mappings
- Exiting TrafficDOT
- X Mode LED Displays for Slot Numbers
- Circuit-board Dip Switch SW1 Settings
- Circuit-board Dip Switch SW2 Settings
- Pre-Installation Worksheets
- Contact Closure Card External Interfaces
Appendix E
56 Access Point Controller Card (APCC)
Installation Guide Sensys Networks, Inc.
Backplane Edge Connections
Pin Function (TS1 mode) Function (TS2 mode)
1 Not connected Channel 1 Delay enable
2 Not connected Channel 2 Delay enable
3 Address 3 Address 3
4 Daisy chain RS485 Uplink + Daisy chain RS485 Uplink +
5 Daisy chain RS485 Uplink - Daisy chain RS485 Uplink -
6 Address 0 Address 0
7 Not connected Channel 1 status
8 Daisy chain RS485 Downlink + Daisy chain RS485 Down-
link +
9 Daisy chain RS485 Downlink - Daisy chain RS485 Down-
link -
10 Address 1 Address 1
11 AC power neutral AC power neutral
12 AC power line AC power line
13 Not connected Not connected
14 Not connected Not connected
15 Address 2 Address 2
16 Not connected Channel 3 status
17 Not connected Not connected
18 Not connected Not connected
19 Not connected Not connected
20 Not connected Channel 2 status
21 Not connected Not connected
22 Not connected Channel 4 status
A GND GND
B 24V 24V
C Reset input Reset input
D Not connected Not connected
E Not connected Not connected
F Channel 1 collector Channel 1 collector