User's Manual

SENTON Enterprises Limited 信 通 企 業 有 限 公 司
Flat 10, 17/F, Fo Tan Industrial Centre, 香港沙田火炭坳背灣街 26-28 號
26-28 Au Pui Wan Street, Fo Tan, Shatin, N.T., Hong Kong 富騰工業中心 17 樓 10 室
Tel: [phone] Fax: [phone] 電話: (八五二) 二六八七 一七一二 (四線)
E-mail address: [e-mail]
傳真: (八五二) 二六八七 四一二五
20 030206A-1
K. ID SET (for Handset 1 and Handset 2) [ NOTE: ID SET had been preset at the factory. The user
doesn’t need to do the ID SET. If the handset can not be linked up with base unit properly, please
reset the ID SET. (Reset ID SET: The user must delete the base ID, and then do the ID SET.) ]
1. Press and hold the SCAN/MENU button.
2. Press the
* button once.
3. Press the SAVE/PHONE BOOK button.
The LCD will indicate PRESS PAGE.
4. Press and hold the page button until beeping on the handset, and then the handset will indicate
ID success.
DELETE BASE ID:
1. Press and hold the page button about 4 seconds, and then the base IN USE LED will light up .
2. Press and hold the page button about 2 seconds, and then the base IN USE LED will flash.
3. Press again the page button , and then the base IN USE LED will turn off.
ANSWERING MACHINE OPERATION
The 36028 features a sophisticated Digital Answering System. Incoming Messages (ICMs), Outgoing
Message (OGM) and Memo messages are stored electronically into digital memory. Messages are
accessed instantly and arranged compactly in this memory. The 36028 can store 15 minutes of message
(ICMs, OGM and Memos Combined).
NOTE: The maximum incoming Message (ICM) recording time is 1 minutes. The minimum incoming
Message (ICM) recording time is 3 seconds.
VOICE MENU SYSTEM
A sophisticated Voice Menu System has been designed and pre-programmed into the 36028. This system
will verbally guide you through key operational procedures.
TIME/DAY STAMP
ICMs and Memo messages are automatically voice-stamped with the current time and day.
NOTE: After power failure, the time/day stamp will be lost. In this case, the time will be incorrect. Please
refer to the INITIAL SETUP section on how to set the system time and day.
SETTING ANSWER ON/OFF/A(Announce)
The unit defaults to Answer ON automatically after power up.
1. With recording OGM in standby mode ( “ON” mode) and without recording OGM in “A” mode.
A. TO TURN ANSWER MODE OFF
1. In standby mode, press the ANS. ON/OFF button on the base unit until you hear “Answering machine
is off ”.
2. The 36028 will announce “Answering machine is off ”.
NOTE: If the Answering Mode is OFF, the 36028 will answer after the 10
th
ring. (When the second caller
call in. The “OFF” mode will automatically return to “ON” mode)
B. TO TURN ANSWER MODE ON
1. In standby mode, press the ANS. ON/OFF button until you hear “Answering machine is on ”.
NOTE: The 36028 will answer after ringing.
C. TO TURN ANSWER MODE A
1. In standby mode, press the ANS. ON/OFF button until you hear “Answering machine is A”.
Note: THE 36028 will say “ Sorry mailbox is full, please try again later” after ringing, and then will
automatically hang up after hold seven seconds.
2. With recording OGM in “A” mode and in “ON” mode.
TO TURN ANSWER MODE A: THE 36028 will indicate “ host recorded OGM in the “A” mode” after
ringing, and then will automatically hang up.
ID SET
#
11
TOTAL
11