User's Manual

SENTON Enterprises Limited 信 通 企 業 有 限 公 司
Flat 10, 17/F, Fo Tan Industrial Centre, 香港沙田火炭坳背灣街 26-28 號
26-28 Au Pui Wan Street, Fo Tan, Shatin, N.T., Hong Kong 富騰工業中心 17 樓 10 室
Tel: [phone] Fax: [phone] 電話: (八五二) 二六八七 一七一二 (四線)
E-mail address: [e-mail]
傳真: (八五二) 二六八七 四一二五
21 030206A-1
3. With recording OGM in “A” mode and without recording OGM in “ON” mode.
A. TO TURN ANSWER MODE ON: THE 36028 will say “ Please leave your message and we will
return your call” after ringing, and then will answer.
B. TO TURN ANSWER MODE OFF: THE 36028 will say “ Please leave your message and we will
return your call” after the 10
th
ring , and then will answer.
C. TO TURN ANSWER MODE A: After ringing and will ring a beep, and then will automatically hang
up.
SETTING THE RINGS SWITCH(TS/4R/2R)
The number of rings before the answering system answers a call be selected by setting the RINGS switch
on the base unit to :
TS – Toll Saver
4 - Four rings
2 - Two rings
Toll Saver lets you avoid unnecessary toll charges when calling long distance to remotely retrieve your
messages.
The 36028 can be set to answer the first call on the 4
th
ring, and all subsequent calls on the 2
nd
ring by
setting the RINGS switch on the Toll Saver (TS) position. If your 36028 fails to answer on the 2
nd
ring ,
then you know that you do not have any new incoming Message(s)(ICM). You can hang up before the
unit answers and save the cost of the call.
SETTING TIME/DAY
1. Press “TIME SET” button. You will hear current Time/Day setting the time and day.
2. Press and hold “TIME SET” button for about 3 seconds. You will hear “Sunday”.
3. Press “SKIP
” or “REPEAT ” button (on the base) until the correct day is announced.
4. Press “TIME SET” button to confirm and then set the hours. You will hear “12AM” as the “12AM” is
displayed in message counter.
5. Press “SKIP
” button to advance or “REPEAT ” button to reverse the hour show in the display.
6. Press “TIME SET” button to confirm and then set the minutes, you will hear “00” as the “00” is
displayed in message counter.
7. Press “SKIP
” button to increment or “REPEAT ” button to decrement the minute in the
display.
8. Press “TIME SET” button to confirm. The new day and time will announced.
SETTING CODE
1. Press CODE button on the base. Then you will hear the current setting, “one, two, three”.
2. Press and hold “code” button for about 3 seconds.
3. Press Skip
or Repeat button (on the base) to select the first digit you desired.
4. Press the CODE button to confirm.
5. Press Skip
or Repeat button to select the second digit you desired.
6. Press the CODE button to confirm.
7. Press Skip
or Repeat button to select the third digit you desired.
8. Press the CODE button to confirm.
You will hear the newly programmed 3-digit security code.
NOTE: When the 36028 is disconnected the AC Adaptor from the base beyond five hours, the code will
be returned to the original setting “159”.
OUTGOING MESSAGE (OGM)
This is the announcement callers will hear when 36028 answers a call. The 36028 also has a default
OGM(factory preset) which is active when there is no OGM present.
Default OGM: “Please record your message after the beep.”