5GHz AUDIO TRANSCEIVER PANDA / ATM210 DATASHEET REV 00 June 10, 2019 SEONG JI INDUSTRIAL CO.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 ▶ CONTENTS 1. Revision History .......................................................................................................................................................... 3 2. Scope ........................................................................................................................................................................ 4 3. Product Information ........................................................
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 1. Revision History No.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 2. Scope This document is the specifications of 5GHz wireless audio transceiver module, ATM210. 3. Product Information 3-1. Product Information ITEMS DESCRIPTION Manufacturer Product type Product application Project Name Model Name Part Number Regulatory Certification SEONG JI INDUSTRIAL CO,.LTD Wireless Audio Transceiver Mono/Stereo wireless audio system PANDA ATM210 WSATM210x00 FCC 2AS8LATM210 IC 25119-ATM210 CE TBD 3-2.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 4. Introduction The ATM210 is 5GHz AUDIO TRANSCEIVER that optimized for building point to multi-point digital wireless audio solutions such as wireless subwoofers and wireless rear speakers in home theater system. This wireless audio module provides a highly-integrated and flexible wireless audio solution based on the AV5100 SoC.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 The hardware for the audio input (transmit) and audio output (receive) versions of the module is identical and only the firmware loaded onto the module determines its function. Features Product Size - Module Size (mm): 40.4 (W) X 26.0 (L) X 3.2 (H) - PCB size (mm): 40.0 (W) X 2.6.0 (L) x 1.1 (H) - Shield can (mm): 24.7 (W) X 21.9 (L) X 2.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 5. Electrical Specifications 5-1. Absolute Maximum Ratings Absolute Maximum Ratings (AMR) are stress ratings only. AMR corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Stresses beyond those listed under AMR may cause permanent damage to the device.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 Continuous TX 110 Linked status for TX 49 Searching for TX 46 Continuous RX 110 Linked status for RX 93 Searching for RX 93 0.6 Input Voltage Logic Low, VIL CMOS I/O Logic Levels – VDDIO 3.3V Input Voltage Logic High, VIH VDDIO 0.6V 0.3 Output Voltage Logic Low, VOL Output Voltage Logic High, VOH mA V VDDIO 0.3V 5-4. Electrical Characteristics – RF TX Operating Conditions: VDD = 4.5 to 5.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 5-5. Electrical Characteristics – RF RX Operating Conditions: VDD = 4.5 to 5.5V, TA = 0°C to +60 °C, RF Freq = 5725‐5825MHz, measured to the RF conducted 2 ports. Typical specifications at TA = 25°C, VDD = 5.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 16bit audio, 14.8KSps over-the-air sample rate 16bit audio, 14.8KSps over-the-air sample rate 16bit audio, 14.8KSps over-the-air sample rate 16bit audio, 14.8KSps over-the-air sample rate Gain Flatness 0dB Input / Output Gain SNR I2S Input / Output 20 6.5K 20 10K 20 13K 20 20K +/- 0.2 dB 93* THD+N dB 94 dB * 16bit audio, all OTA sample rate. OTA 12-bit path for voice is possible, but will limit the SNR to 72dB 5-8.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver I2S 32-96K SRC 2 (Audio) USB 8K-48K ECU (TX) “14.8K” REV: 00 I2S Maser : 48K Slave : 44.1K-96K USB 8K-48K All rate support 16bit, > 93dB, but the OTA 12bit path will limit SNR to 72dB ECU (TX) “14.8K” Actual bandwidth is dependent on the lower of the input or output rate Output BW vs OTA “11K” = 5KHz “14.8K” = 6.5KHz “22K” = 10KHz “29.6K” = 13KHz “44K” = 20KHz 5-9.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 THd Hold time 25 TOd Output delay -25 Bit clocks/Word clock ns 25 ns 64 I2S protocol is “I2S Justified” as shown below. *The timing specified for the rise and fall times represents the edge rates on the module itself. The rise and fall times of the I2S signals are determined by ESD/EMI mitigation components on the modules, as well as external loading, and will be higher than the specified numbers 5-10.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 I2C Slave Interface Timing (Fast-Mode) Parameter MIN MAX UNIT VIL Low level input voltage -0.3 0.8 V VIH High level input voltage 2.0 3.6 V 0 0.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 6.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 7. Mechanical Specifications 7-1. Module dimension 7-2.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 8.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 9. Certificate Statement FCC & IC Statement This AUDIO TRANSCEIVER has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC / IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC / IC approvals must be obtained.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 Device Classifications Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission, and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 OEM Instruction Manual Content Consistent with §2.909(a), the following text must be included within the user’s manual or operator instruction guide for the final commercial product (OEM-specific content is displayed in italics.) Operating Requirements and Conditions: The design of ATM210 complies with U.S. Federal Communications Commission (FCC) guidelines respecting safety levels of radio frequency (RF) exposure for Mobile devices.
PBA RF Module ATM210 5GHz Wireless Audio Transceiver REV: 00 Information This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils radio exempts de licence.
