AKR-100 Full Manual V.1.
AKR-100 Full Manual V.1.5 GENERAL SAFETY AND PRECAUTIONS This AKR-100 is manufactured to satisfy international safety standards. Review the following safety precautions to avoid injury and prevent damage to the AK-30 or any products connected to it. 1. Use a proper power source. Do not operate this product from a power source that applies more than the specified voltage (DC12V). 2. Never insert anything metallic into the AKR-100 - this can cause electric shock. 3. Do not operate in wet & dusty conditions.
AKR-100 Full Manual V.1.5 TABLE OF CONTENTS Chapter 1: Packing Contents CONTENTS IN THE PACKAGE 05 Chapter 2: Getting To Know Your AKR-100 AKR-100 06 Chapter 3: Remote control REMOTE CONTROL PANEL 08 Chapter 4: Getting Started OVERVIEW OF SET UP PROCEDURES 09 Chapter 5: Hardware Installation SD MEMORY INSTALLATION 10 CONNECTING AKR-100 TO YOUR TV SET OR MONITOR 10 ALARM INSTALLATION 11 Chapter 6: AKR-100 Menu 1. ACCESS TO OSD MENU 13 2. MAIN MENU 13 3. RECORD MODE 14 4.
AKR-100 Full Manual V.1.5 7.1 PASSWORD CHANGE 7.2 TIME SET 7.3 BRIGHTNESS 7.4 AUDIO 7.5 VIDEO 7.6 MEMORY SYNC 20 20 21 22 22 8.
AKR-100 Full Manual V.1.
AKR-100 Full Manual V.1.5 Chapter 2: Getting To Know Your AKR-100 ▶ AKR-100 ③ ② ④ ⑤ ⑦ ⑥ ⑧ ⑨ ⑩ ① This chapter briefly describes the functions of each button on AKR-100. The buttons are used to operate the basic functions of AKR-100, such as recording, playback, fast-forward, reverse play and etc. For more details on the set-up and operation of AKR-100, refer to Chapter 6, AKR-100 MENU. 1 Sensor-in / Alarm-out The sensor terminal block is used to connect a sensor such as PIR to the AKR-100.
AKR-100 Full Manual V.1.5 2 SD Memory Slot Insert SD Card into the slot for storing data. 3 Recording LED This light indicates while AKR-100 is on recording mode. 4 Status LED This light blinks when events occur or there is any error.. 5 Power LED This light indicates the AKR-100is powered up. 6 Remote control Receiver When controlling AKR-100 by remote control, be sure to point at the receiver. 7 Reset Press the reset button if you want to return setting values to the default.
AKR-100 Full Manual V.1.5 Chapter 3: Remote control 1 REC: The button to start recording or stop recording 2 MENU: The button to enter ‘MENU’ mode. 3 UP/ DOWN: The buttons to choose a menu field and change a value. 4 FF: The button to play recorded video forward. REW: The button to play recorded video backward. 5 REW: The button to play recorded video backward. 6 FF: The button to play recorded video forward. 7 PLAY: The button to start video playback. 8 STOP: The button to stop playback.
AKR-100 Full Manual V.1.5 Chapter 4: Getting Started OVERVIEW ON SET-UP PROCEDURES Below is an overview of the installation steps required get your AK-30 unit working. Each step is explained in detail in Chapter 5 - Hardware Installation. (1) Insert a SD MEMORY. (2) Connect AKR-100 to a TV set or monitor. (3) Connect camera to AKR-100. (4) Connect optional accessories (sensors or alarm). (6) Connect the power. (7) Turn the power on. (8) Start TV Monitoring and recording.
AKR-100 Full Manual V.1.5 Chapter 5: Hardware Installation SD MEMORY INSTALLATION ① Format SD Memory Insert SD memory into SD card slot on your PC and format it in FAT32. ※ In case there is no card slot on your PC, use additional memory reader device. ② Insert SD Memory into SD slot on AKR-100 After formatting, take SD Memory from your PC and insert it into SD slot on AKR-100. ③ Backup recorded files in SD Memory When SD Memory storage is full, the recorded files can be backed up in your PC.
AKR-100 Full Manual V.1.5 To display images from the AKR-100, connect the video output signal to your monitor or Television. Any Television with a VIDEO INPUT terminal is suitable for displaying the images. The diagram above shows the video signal connections. Connect the camera to VIDEO-IN terminal of AV-IN connector; connect the monitor to VIDEO OUT terminal of AV-OUT connector. Note: The RCA cable required for this connection is not included in the package of AKR-100.
AKR-100 Full Manual V.1.5 Note: Contact an authorized dealer for information about buying the appropriate alarm device for your needs and for information concerning proper installation procedures.
AKR-100 Full Manual V.1.5 Chapter 6: AKR-100 Menu 1. ACCESS TO OSD MENU AKR-100 1.0 **** Press ‘MENU’ button on remote control to access to AKR-100 OSD menu. Please refer to ‘Chapter 3: Remote control’ about how to use remote control buttons. Password is ‘0000’ as default. The password can be changed on ‘[SUB MENU]Æ[PASSWORD CHANGE]’. In order to select cameras for recording, set recoding quality, schedule recording times and to set other operation parameters, you will need to access the AKR-100’s menu.
AKR-100 Full Manual V.1.5 In the main menu, the ‘indicator ‘■’ will be shown on the left of each menu. Press ‘UP/DOWN’ button on remote control to select a desired menu. After placing ‘■’ on the desired menu and press ‘ENTER’ button to enter the menu. 3. RECORD MODE 3. RECORD MODE 3.1 OVERWRITE (ON/OFF): If this option is ON, recording keeps going on by deleting old recorded files when SD memory storage capacity is full. If it is OFF, the recording session stops when all SD Memory is full. 3.
AKR-100 Full Manual V.1.5 4. VIDEO QUALITY 4. VIDEO QUALITY 4.1 LEVEL (HIGH / NORMAL / LOW): Select desired video level from ‘LOW’ to ‘HIGH’. Compression Bitrate for HIGH: 1.2Mbps Compression Bitrate for Normal: 750Kbps Compression Bitrate for Low: 500Kbps 4.2 POST RECORDING TIME: Post recording time means the time between one event and the next one. 1 second to 30 minutes can be set up. 4.3 FRAME RATE PAL: Selectable among 25 / 12 / 8 / 6 / 5 / 1 / 0.5 / 0.2 /0.
AKR-100 Full Manual V.1.5 5. EVENT MODE 5.1 ALARM SETUP 5.1.1 ALARM INPUT (ON / OFF): Select ‘ON’ if you want to use alarm input device. 5.1.
AKR-100 Full Manual V.1.5 sensor recording starts automatically. In NORMAL-OPEN mode, if an intruder cuts the cable line that connects the sensor to the AKR-100, the sensor recording will not start at. 5.1.3 ALARM OUTPUT (ON / OFF): Select ‘ON’ if you want to use alarm output device 5.1.4 TYPE: Select alarm output type between ‘NO’ and ‘NC’. 5.2 MOTION SETUP 5.2.1 MOTION (ON / OFF): Select ‘ON’ if you want to use motion detection. 5.2.
AKR-100 Full Manual V.1.5 5.3 SCHEDULE SETUP MON to FRI 00:00 ~ 09:00 MON to FRI 18:00 ~ 23:59 MON to FRI 00:00 ~ 09:00 OFF The recording time can be scheduled on this menu. Up to 4 schedules can be set up. Configure period of time when recording is available. 6. SEARCH TIME 2007 / 01 / 01 2007 / 01 / 31 SEARCH 00:00 23:59 The recorded files in SD Memory can be easily searched through ‘SEARCH’ menu. After entering searching option in the fields, click ‘SEARCH’ to bring search result. 6.
AKR-100 Full Manual V.1.5 6.1.2 SEARCH MODE – EVENT: When you select ‘EVENT (or BOTH) on SEARCH MODE’, additional search conditions opens; ALARM / EMERG (Emergency) / MOTION You can select 2 or more conditions simultaneously (ALARM / EMERG / MOTION). 6.1.3 SEARCH MODE – BOTH: Configure search condition as both ‘TIME’ and ‘EVENT’. 7. SUB MENU To change a password, navigate to PASSWORD CHANGE in the SUB MENU and press the select button [ENT].
AKR-100 Full Manual V.1.5 7.1 PASSWORD CHANGE The Factory Default Password is 0000. To enter this number, press the UP/DOWN button on the remote control. Once you input the your current password, set a new six digit password using the buttons UP, REW, DOWN, FF on the remote control. Then, confirm your new password by entering the number again. 7.2 TIME SET Configure current time and ‘day light saving’ option.
AKR-100 Full Manual V.1.5 7.3 BRIGHTNESS Select brightness value among low, medium and high. 7.4 AUDIO ON Audio function can be turned OFF or ON in the menu. Note: When you do audio recording, you have to set the RECORD FRAMERATE over 4. If you set it under 4(1,2 or 3), audio recording cannot be supported.
AKR-100 Full Manual V.1.5 7.5 VIDEO NTSC AKR-100 automatically recognizes video mode. When you connect NTSC camera to AKR-100, it detects the camera source accordingly. However, when you playback recorded files in SD card on AKR-100, you should select right video mode in order to avoid image distortion. 7.6 MEMORY SYNC YES The index file is automatically generated and stored in SD card inserted into AKR-100.
AKR-100 Full Manual V.1.5 8. DEFAULT YES To reset AKR-100 settings back to the factory default, select ‘YES’ and enter it. After resetting, the password will return to the default value (0000) as well as all settings of AKR-100 on the menu. To reset to factory default will not erase any video data in SD card.
AKR-100 Full Manual V.1.5 APPENDEX SPECIFICATION ITEM VIDEO Video Input Format Operating system Video Input Channels Video Output Channels Input Level Main TV Output 1 Display Resolution Display frame rate DESCRIPTION PAL / NTSC auto detection function RTOS in firmware 1CH Composite video 1CH Composite video 1.0Vp-p +/-10% Composite, 75 Ohm Unbalanced 1.
AKR-100 Full Manual V.1.5 RECORDING CONDITIONS Based on 1GB of storage with the installation of 1 camera Approximate Recording Time Table Mode HIGH(30frame) NORMAL(30frame) LOW(30frame) REMARK Video Quality 1200Kbps 700Kbps 500Kbps - Recording Time 7,054 Sec 8,830 Sec 9,492 Sec 1GB (Actual storage space 900MB) * Recording time can differ according to SD card kinds.
AKR-100 Full Manual V.1.5 Seorim Technology Co., Ltd #1001, daerung technotown vi, 493-6, gasan-dong, kumchun, seoul, korea, 153-803 Tel: +82-2-2108-5860 Fax: +82-2-2108-5869 E-mail: sales@seorimtech.com http://www.seorimtech.