User Manual

ManualsBrandsSercomm ManualsElectronicsRCA WiFi Enabler

Quick Installation Guide

802.11g/802.11b Access Point/Router

1. Introduction

Package Contents

The following items should be included:

If any of the above items are damaged or missing, please contact your dealer immediately.

Physical Details

Front Panel LEDs

Power

On - Normal operation.

Off - No power

LAN

On - The LAN (Ethernet) port is active.

Off - No active connection on the LAN (Ethernet) port.

Flashing - Data is being transmitted or received via the corresponding LAN (Ethernet) port.

WAN

On - The WAN (Ethernet) port is active.

Off - No active connection on the WAN (Ethernet) port.

Flashing - Data is being transmitted or received via the corresponding WAN (Ethernet) port.

Wireless

LAN

On - Idle.

Off - Error- Wireless connection is not available.

Flashing - Data is being transmitted or received via the Wireless access point. Data includes

"network traffic" as well as user data.

Mode

On – AP mode

Off – Router mode

WPS

Following WPS standard SPEC

Summary of content (6 pages)

PAGE 1
Quick Installation Guide 802.11g/802.11b Access Point/Router 1. Introduction Package Contents The following items should be included: If any of the above items are damaged or missing, please contact your dealer immediately. Physical Details Front Panel LEDs Power On - Normal operation. Off - No power LAN On - The LAN (Ethernet) port is active. Off - No active connection on the LAN (Ethernet) port. Flashing - Data is being transmitted or received via the corresponding LAN (Ethernet) port.
PAGE 2
Rear Panel Antennae Reset Button One antenna is supplied. Best results are usually obtained with the antennae in a vertical position. This button has two (2) functions: Reboot. When pressed and released, the Wireless Access Point will reboot (restart). Reset to Factory Defaults. This button can also be used to clear ALL data and restore ALL settings to the factory default values, as follows: 1. Power off the Access Point. 2. Hold the Reset Button down while you Power On the Access Point. 3.
PAGE 3
WPS Button The button is for WPS function: After pressed and released, router enter into mode which can support WPS client to connect Ethernet LAN Ethernet WAN Use a standard LAN cable (RJ45 connectors) to connect this port to a 10BaseT or 100BaseT hub on your LAN. Use a standard LAN cable (RJ45 connectors) to connect this port. In AP mode, connect this port to a 10BaseT or 100BaseT hub on your LAN. In Router mode, connect this port to a DSL modem Connect the supplied power adapter here. Power port 2.
PAGE 4
3. If used as router, use a standard LAN cable to connect the “Wan” port on the Wireless Access Point to DSL modem. 4. Connect the supplied power adapter to the Wireless Access Point and a convenient power outlet, and power up. 5. Check the LEDs: • The Power, Wireless LAN, and LAN LEDs should be ON. 3. Access Point Setup The default settings are: • SSID: Thomson • WPA-PSK: Enabled • Key: Generate from MAC address If you need to change these, follow this procedure. 1.
PAGE 5
Note: The CD-ROM contains a Windows utility which can be used to assist setup. 4. Client (PC) Configuration WEP/WPA-PSK Mode Each Wireless Station must have the same settings as the Wireless Access Point. Mode On each PC, the mode must be set to Infrastructure. SSID This must match the value used on the Wireless Access Point. (ESSID) The default value is default Note! The SSID is case sensitive.
PAGE 6
Regulatory Approvals FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.