ADT Pulse® Interactive Solutions OC835-ADT Quick Installation Guide
Table of Contents CHAPTER 1 INTRODUCTION ............................................................................ 3 Overview............................................................................................................... 3 Physical Details ................................................................................................... 4 Package Contents ............................................................................................... 6 CHAPTER 2 BASIC SETUP ..............
Chapter 1 Introduction 1 This section provides information about the OC835-ADT Outdoor Day/Night HD Camera's features, components and capabilities. Overview The OC835-ADT is a true outdoor day/night wireless camera with HD resolution, 802.11n Wi-Fi connectivity and Wi-Fi Protected Setup (WPS) support. This camera is intended for use with ADT Pulse ®. Features x Standalone Design. The camera is a standalone system with built-in CPU and video encoder.
Chapter 1 Introduction Physical Details Front Light Sensor Lens PIR Sensor Figure 1: Front Panel Light Sensor This is a hardware sensor to detect lux. Lens The lens cannot be adjusted. Please ensure that the lens cover remains clean. PIR Sensor This is a Passive Infrared sensor to detect motion.
Chapter 1 Introduction DC Power Input Connect the supplied 12V power adapter here. Do not use other power adapters; doing so may damage the camera. Power LED (Green, Amber) On (Green). Power on. Off. No power. Blinking (Green). The Power LED blinks during start up for approximately 1 minute. Blinking (Amber). The firmware is being upgraded. On (Amber). The firmware upgrade has failed. Network/Wireless LED (Green, Amber) On (Green). Network connection is available (wired or wireless). Off.
Chapter 1 Introduction Package Contents The following items are included in the package.
Chapter 2 Basic Setup This section provides information on how to assemble and configure the OC835-ADT Outdoor HD Camera. 2 Installation 1. Assemble the Camera Attach the Camera Stand to the camera. 2. Make the Connection Using a Wired Connection If you are using a wired connection to the OC835-ADT, connect a Micro USB to RJ-45 Adapter Cable (not included) to the USB port of the camera. Then use a standard Ethernet cable (not included) to connect to the Pulse Gateway or Total Security (TS) Base panel.
Chapter 2 Basic Setup Use only the power adapter provided. Using a different one can result in hardware damage. Figure 5: Routing the Power Cable The Power LED turns on briefly, and then starts blinking. (The Power LED will continue to blink during startup, which takes about one minute. After startup is completed, the Power LED should remain ON.) 4. Check the LEDs x Power LED. At power up, the Power LED turns on briefly, and then starts blinking, which takes about one minute.
Chapter 3 ADT Pulse Enrollment 3 This section provides examples of three different methods for enrolling the OC835-ADT Outdoor HD Camera into the ADT Pulse network. (1) The first method uses a wired connection to enroll the HD Camera to a Gateway via the Pulse Portal. (2) The second method, which uses WPS to wirelessly enroll the HD Camera to a Gateway via the Pulse Portal, is described on page 13.
Chapter 3 ADT Pulse Enrollment 5. In the Manage Devices screen, click Cameras. 6. Click the Add button at the bottom of the screen. 7. On the rear of the camera locate the camera’s MAC ID.
Chapter 3 ADT Pulse Enrollment 8. On the Add Camera screen, enter the camera’s MAC ID. Do not click Continue at this time. 9. Ensure that the camera is connected to the device port of the Gateway using the Micro USB to RJ-45 Adapter Cable / Ethernet cable and connected to the supplied 12VDC power adapter. 10. After the Power and Network LEDs turn on solid green, click Continue. 11. Wait for the camera to add. It could take a few minutes, especially if an upgrade is required.
Chapter 3 ADT Pulse Enrollment 12. Assign the camera a unique name (usually based on the location of the camera) in the Name field, and then click the Save button at the upper right of the screen. 13. The Cameras screen appears, now displaying the added camera. 14. At the top left of the screen, click Go Back. 15. You are returned to the Manage Devices screen. The total number of installed cameras has increased by one. Click Close. 16. Click Close again to confirm. 17.
Chapter 3 ADT Pulse Enrollment Wireless Connection to the Gateway Using the Pulse Portal 1. Set up the camera, as described in Chapter 2. 2. Open a web browser and in the address bar, enter: https://Portal.ADTPulse.com. 3. Type your Username and Password, and then click the Sign In button. 4. Click the System tab, and then click the Manage Devices button. 5. In the Manage Devices screen, click Cameras.
Chapter 3 ADT Pulse Enrollment 6. In the Cameras screen, click the Add Using WPS button at the bottom of the screen. 7. Locate the PIN number located on the label on the rear of the camera and enter that number in the WPS PIN field. 8. Ensure that the camera is powered on, and then click the Continue button to initiate the WPS process.
Chapter 3 ADT Pulse Enrollment The following screen appears. 9. Press and hold the WPS/RESET button on the camera for 5 seconds to establish a wireless connection. Note: You must complete the WPS connection within 2 minutes or else the process will time out. The time remaining is displayed in the upper left portion of the screen. The Network/WPS LED flashes amber as the Gateway attempts to connect to the camera. The wireless connection is successful when the Network/WPS LED turns solid green.
Chapter 3 ADT Pulse Enrollment 10. When the Camera Details screen appears, showing that the camera has been enrolled, assign the OC835-ADT a unique name (usually based on the location of the camera) in the Name field, and then click Save. The new camera appears in the Cameras list. 11. At the top left of the screen, click Go Back. 12. You are returned to the Manage Devices screen. The total number of installed cameras has increased by one. Click Close. 13. Click Close again to confirm. 14.
Chapter 3 ADT Pulse Enrollment Wireless Connection to the TS Base Using the Installer App Note: In ADT Total Security (TS) Systems, the gateway is integrated with the TS Base panel and is not a separate device. 1. Install and configure the camera, as described in the previous chapter. 2. Launch an Internet browser from a computer and log in to the Installer App. 3. Select Pulse Devices. 4. Click Cameras.
Chapter 3 ADT Pulse Enrollment 5. Click the Add Using WPS button, located at the bottom of the screen. 6. Locate the PIN number located on the label on the rear of the camera and enter that number in the WPS PIN field. 7. Ensure that the camera is powered on, and then click the Continue button to initiate the WPS process.
Chapter 3 ADT Pulse Enrollment The following screen appears. 8. Press and hold the WPS/RESET button on the camera for 5 seconds to establish a wireless connection. The Network/WPS LED flashes amber as the TS Base attempts to connect to the camera. The wireless connection is successful when the Network/WPS LED turns solid green. Note: You must complete the WPS connection within 2 minutes or else the process will time out. The time remaining is displayed in the upper left portion of the screen. 9.
Chapter 3 ADT Pulse Enrollment The Pulse enrollment is complete. The newly-added device appears in the Cameras list. 10. At the top left of the screen, click Go Back. 11. Disconnect the camera from power. 12. Install the camera in its final location. For Wall Mounting, refer to Chapter 4. If the Camera Continually Goes Offline If after enrolling it the camera, it continually goes offline (Power LED blinks continually), the camera will automatically attempt to recover the wireless connection.
Chapter 4 Wall Mounting 4 This section provides details for final mounting of the OC835-ADT Outdoor Day/Night HD Camera. You should ensure that the camera is configured and enrolled in ADT Pulse before permanently mounting it. Mounting Suggestion. To get the best video quality for targets at night, make sure that the camera’s field of view does not include a large foreground object, such as tabletop or side wall. If installing on a tabletop, place the camera as close to the edge as possible.
Chapter 4 Wall Mounting 6. Connect the power cable into the back of the camera, and then insert the grommet as shown in the figures below. Figure 8: Attaching the Power Cable Ensure that the grommet is positioned properly to prevent water from entering the camera. 7. Rotate the power input cover to tighten it, providing a watertight seal for the power cable. Figure 9: Securing the Power Cable 8. Plug the adapter end into a power outlet. 9. Adjust the camera to a desired position and secure it firmly. 10.
Appendix A Specifications A OC835-ADT Outdoor Day/Night HD Camera Dimensions WxHxD 2.99” x 2.99” x 1.91” (76mm x 76mm x 48.6mm) Video Compression H.
Thiss equipment generatess, uses and ccan radiate radio frequ uency energgy and, if not installed an nd used in aaccordance with the instructions, may cause harmful o radio comm munication s. However, r, there is no o guaranteee that inteerference to inteerference will not occurr in a particcular installaation.
FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co located or operating in conjunction with any other antenna or transmitter. CAN ICES 3 (B)/ NMB 3(B) This device complies with RSS GEN of the Industry Canada Rules.
IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
