Quick Start Guide

ManualsBrandsSercomm ManualsComputers & AccessoriesAC2100 Wi-Fi Mesh Extender / AC2100 Wi-Fi Mesh Router

Setup the RP362M

The RP362M extends the range of your existing WiFi network without the

need for running cables. During the installation process, the RP362M

connects to your current WiFi router over WiFi to extend your home network

coverage.

You can set up your RP362M using WPS or your web browser.

Setup Using WPS

Step 1: Make sure the WiFi router is on and working properly.

Step 2: Plug the RP362M into a wall outlet near the WiFi router during setup.

Step 3: Wait for the Power LED to become solid green, the RP362M is now

ready for setup.

Step 4: Push the WPS button on the WiFi router to enable WPS mode. The

LED on the router will blink and WPS will stay active for 2 minutes.

Step 5: Push and hold the WPS button on the RP362M for more than 2

seconds. The WPS LED on the device will start blinking for 2 minutes. The

RP362M will automatically connect to the WiFi router.

Step 6: The connection between the RP362M and WiFi router is complete

after the WiFi LED turns solid green and remains on.

Step 7: Now move the RP362M to a suitable location. Place the extender 1 or

2 rooms away from your existing WiFi router. Check the WiFi LED color on the

RP362M and make sure it’s not solid red.

If the WiFi LED is solid red, move the RP362M closer to the

WiFi router.

Step 8: After setup, the RP362M extends the network using the same SSID

and password from your current WiFi router.

RP362M

Setup Using Web Browser

Step 1: Make sure the WiFi router is on and working properly.

Step 2: Plug the RP362M into a wall outlet near the WiFi router during setup.

Step 3: Wait for the Power LED to become solid green, the RP362M is now

ready for setup.

Step 4: Connect an Ethernet cable to the RP362M and your PC.

Step 5: Launch the browser and enter

http://192.168.0.1

in the Address box.

Step 6: You will be prompted for a username and password. Use the default

values, admin for the username, and WPS PIN for the password.

Step 7: Choose the Wizard page, the RP362M will start to search for existing

WiFi 5GHz networks. If RP362M doesn’t connect to a WiFi router, it will

redirect to Wizard page when user logs in next time.

RP362M

Step 8: Select your desired SSID for the RP362M to connect. A 5GHz

channel is recommended to be used for this connection (Ch. 36-165). Click

Next.

Step9: The Security Settings screen will be shown automatically if your WiFi

router is using encryption. Enter your WiFi router security key. Click

Next.

Step 10: The Extended Network Settings screen will be prompted

automatically if the security is enabled. It is recommended to click “Clone

Settings” to use your existing WiFi router SSID and password or you can enter

a new SSID and password you would like for the extender network. Click Next.

Step 11: Wait until the RP362M connects to the router and the browser moves

to the System Status screen.

Step 12: Now move the RP362M to a suitable location. Place the extender 1

or 2 rooms away from your existing WiFi router. Check the WiFi LED color on

the RP362M and make sure it’s not solid red.

If the WiFi LED is solid red, move the RP362M closer to the

WiFi router.

Step 13: After setup, the RP362M extends the network using the same SSID

and password from your current WiFi router.

Appendix A

Regulatory

FCC Statement

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not

expressly approved by the party responsible for compliance could void

the user's authority to operate this equipment. (Example - use only

shielded interface cables when connecting to computer or peripheral

devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 20 centimeters

between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.