User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
5
Cisco RV180/RV180W Administration Guide 103
DRAFT - CISCO CONFIDENTIAL
Configuring Virtual Private Networks (VPNs)
and Security
This chapter describes VPN configuration, beginning with the “Configuring
VPNs” section on page 103.
It also describes how to configure router security, beginning with the “Configuring
Security” section on page 117.
The following sections are covered:
• Configuring VPNs, page 103
• Configuring a Basic VPN, page 104
• Configuring Advanced VPN Parameters, page 105
• Configuring Security, page 117
Configuring VPNs
A VPN provides a secure communication channel (“tunnel”) between two gateway
routers or a remote PC client and a gateway router. The following types of tunnels
can be created:
• Gateway-to-gateway VPN—Connects two or more routers to secure traffic
between remote sites.
• Remote Client (client-to-gateway VPN tunnel)—A remote client, such as a
PC running VPN client software, initiates a VPN tunnel. The IP address of the
remote PC client is not known in advance. The gateway acts as responder.
Creating Cisco QuickVPN Client Users
To use the Cisco QuickVPN, you must do the following: