User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Introduction
Getting to Know the Cisco RV180
Cisco RV180/RV180W Administration Guide 5
1
DRAFT - CISCO CONFIDENTIAL
Back Panel
RESET Button—The Reset button has two functions:
• If the Cisco RV180 is having problems connecting to the Internet, press the
RESET button for less than five seconds with a paper clip or a pencil tip.
This is similar to pressing the reset button on your PC to reboot it.
• If you are experiencing extreme problems with the Cisco RV180 and have
tried all other troubleshooting measures, press and hold in the RESET
button for 10 seconds. This will restore the factory defaults and clear all of
the Cisco RV180 settings.
LAN Ports (1-4)—These ports provide a LAN connection to network devices,
such as PCs, print servers, or additional switches.
WAN Port—The WAN port is connected to your Internet device, such as a cable or
DSL modem.
ON/OFF Power Switch—Press this button to turn the Cisco RV180 on and off.
When the button is pushed in, power is on.
Power Port—The power port is where you connect the AC power cable.