User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Administering Your Cisco RV180/RV180W
Configuring the Discovery Settings
Cisco RV180/RV180W Administration Guide 141
7
DRAFT - CISCO CONFIDENTIAL
STEP 4 (Optional) To receive e-mail logs according to a schedule, configure the
appropriate schedule settings:
• Unit—Select the period of time that you need to send the log: Hourly, Daily,
or Weekly. To disable sending of logs, select Never. This option is useful
when you do not want to receive logs by e-mail, but want to keep e-mail
options configured so that you can use the Send Log function from the Status
> View Logs pages.
• Day—If logs are to be sent on a weekly basis, choose the day of the week.
• Time—Select the time of day when logs should be sent.
STEP 5 Under Logging Policy, choose the type of logging policy. (See Configuring
Logging Policies, page 138.) By default, only IPsec VPN logs are enabled. Others
are disabled.
STEP 6 If you want the router to send logs to a Syslog server, check the box next to a
syslog server field and enter the IP address or Internet Name of the Syslog server
in the Syslog Server field. Choose the logging policy for each syslog server. You
can configure up to 8 syslog servers.
STEP 7 Click Save.
Configuring the Discovery Settings
The Cisco RV180/RV180W supports two types of discovery protocols: Bonjour
and Universal Plug and Play (UPnP).
Configuring Bonjour
Bonjour is a service advertisement and discovery protocol. To configure Bonjour:
STEP 1 Choose Administration > Discovery Settings > Discovery - Bonjour.
STEP 2 Check the Enable box to enable Bonjour on the router. Unchecking this will disable
Bonjour.
STEP 3 In the Bonjour Interface Control Table, you can see on which VLANs Bonjour is
enabled. For example, Bonjour is by default enabled on the default VLAN ID 1. That
means that the Cisco RV180/RV180W advertises itself to all devices connected to