User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Configuring Networking
Configuring the WAN (Internet) Settings
Cisco RV180/RV180W Administration Guide 28
2
DRAFT - CISCO CONFIDENTIAL
STEP 5 Enter MAC Address information. (See Configuring the MAC Address, page 29.)
STEP 6 Click Save.
Configuring L2TP
If you have a Layer 2 Tunneling Protocol (L2TP) connection to the Internet:
STEP 1 Choose Networking > WAN.
STEP 2 From the Internet Connection Type drop-down menu, choose L2TP.
STEP 3 Enter this information:
STEP 4 Enter MTU information. (See Configuring MTU Settings, page 29.)
User Name Enter your username assigned to you by the ISP.
Password Enter your password assigned to you by the ISP.
Secret (Optional) Enter your secret phrase. This phrase is
known to you and your ISP for use in authenticating
your logon.
Connection Type Choose the connection type:
• Keep connected—The Internet connection is
always on.
• Idle Time—The Internet connection is on only
when traffic is present. If the connection is
idle—that is, no traffic is occurring—the
connection is closed. You might want to
choose this option if your ISP charges based
on connection time.
Idle Time If you choose Idle Time as the connection type,
enter the number of minutes after which the
connection terminates. The valid range is 5–999.
My IP Address Enter the IP address assigned to you by your ISP.
Server IP Address Enter the IP address of the L2TP server.