User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Cisco RV180/RV180W Administration Guide 3
DRAFT - CISCO CONFIDENTIAL
Contents
Configuring IPv6 WAN Settings 48
Configuring IPv6 LAN Properties 50
Configuring IPv6 Routing 51
Configuring Static Routing 51
Adding a Static Route 52
Configuring Tunneling 53
Adding an ISATAP Tunnel 53
Configuring Router Advertisement 54
Configuring Router Advertisement Prefixes 55
Chapter 3: Configuring the Wireless Network
(Cisco RV180W) 58
A Note About Wireless Security 58
Wireless Security Tips 59
General Network Security Guidelines 60
Understanding the Cisco RV180W’s Wireless Networks 61
Configuring Basic Wireless Settings 61
Configuring Security 63
Configuring MAC Filtering 65
Configuring Wi-Fi Multimedia 66
Configuring Wireless Network (SSID) Scheduling 67
Configuring Advanced Wireless Settings 68
Configuring Rogue Access Point Detection 69
Enabling Rogue AP Detection 69
Authorizing a Rogue AP 69
Adding and Editing Authorized APs 70
Configuring Wi-Fi Protected Setup 70
Configuring a Wireless Distribution System (WDS) 71
Configuring Load Balancing 72
Chapter 4: Configuring the Firewall 74
Cisco RV180/RV180W Firewall Features 74
Configuring Access Rules 76