User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Configuring Networking
Configuring Routing
Cisco RV180/RV180W Administration Guide 41
2
DRAFT - CISCO CONFIDENTIAL
STEP 1 Choose Networking > LAN > Jumbo Frames.
STEP 2 Check the Enable box.
STEP 3 Click Save.
Configuring Routing
Choosing the Routing Mode
The Cisco RV180/RV180W provides two different routing modes. Network
Address Translation (NAT), or gateway routing, is a technique that allows several
endpoints on a LAN to share an Internet connection. The computers on the LAN
use a “private” IP address range while the WAN port on the firewall is configured
with a single “public” IP address. The Cisco RV180/RV180W translates the internal
private addresses into a public address, hiding internal IP addresses from
computers on the Internet. If your ISP has assigned you a single IP address, you
want to use NAT so that the computers that connect through the Cisco RV180/
RV180W are assigned IP addresses from a private subnet (for example,
192.168.10.0).
The other routing mode, “router,” is used if your ISP has assigned you multiple IP
addresses so that you have an IP address for each endpoint on your network. You
must configure either static or dynamic routes if you use this type of routing. See
Configuring Static Routes, page 43, or Configuring Dynamic Routing, page 45.
To choose your routing mode:
STEP 1 Select Networking > Routing > Routing Mode.
STEP 2 Click the box next to the type of routing to configure.
STEP 3 Click Save.
NOTE If you have already configured DMZ or firewall settings on your firewall in gateway
(NAT) mode, selecting “router” changes those settings back to the default.