User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Configuring Networking
Configuring IPv6
Cisco RV180/RV180W Administration Guide 54
2
DRAFT - CISCO CONFIDENTIAL
STEP 1 Choose Networking > IPv6 > Tu n n el i ng .
STEP 2 In the ISATAP Tunnel Table, click Add.
STEP 3 Enter the tunnel name.
STEP 4 Choose the local endpoint address, or the endpoint address for the tunnel that
starts with the Cisco RV180/RV180W. The endpoint can be the LAN interface (if
the LAN is configured as an IPv4 network), or another LAN IPv4 address.
STEP 5 If you chose Other IP in Step 4, enter the IPv4 address of the endpoint.
STEP 6 Enter the ISATAP subnet prefix. This is the 64-bit subnet prefix that is assigned to
the logical ISATAP subnet for this intranet. This can be obtained from your ISP or
internet registry, or derived from RFC 4193.
STEP 7 Click Save.
To modify the settings of an ISATAP tunnel:
STEP 1 Choose Networking > IPv6 > Tu n n el i ng .
STEP 2 Check the check boxes for the tunnels you want to modify.
STEP 3 Click Edit, make the changes, and click Save.
To delete an ISATAP tunnel:
STEP 1 Choose Networking > IPv6 > Tu n n el i ng .
STEP 2 Check the check boxes for the tunnels you want to delete.
STEP 3 Click Delete.
Configuring Router Advertisement
The Router Advertisement Daemon (RADVD) on the Cisco RV180/RV180W listens
for router solicitations in the IPv6 LAN and responds with router advertisements as
required. This is stateless IPv6 auto configuration, and the Cisco RV180/RV180W
distributes IPv6 prefixes to all nodes on the network.