User's Manual
Table Of Contents
- Introduction
- LAN Ethernet Interfaces
- Wireless Access Point (Cisco RV180W)
- Firewall and VPN Client Access
- Wireless Distribution System (Cisco RV180W)
- Virtual Networks
- Wireless Security (Cisco RV180W)
- Quality of Service (Cisco RV180W)
- Configuration and Administration
- Front Panel
- Back Panel
- Front Panel
- Back Panel
- Installation Guidelines
- Wall Mounting
- Configuring Networking
- Configuring the IPv4 WAN (Internet)
- Configuring PPPoE Profiles
- Configuring IPv4 LAN (Local Network) Settings
- Configuring Virtual LAN (VLAN) Membership
- Configuring Multiple VLAN Subnets
- Configuring Static DHCP
- Configuring Advanced DHCP Settings
- Viewing DHCP Leased Clients
- Configuring RSTP (Cisco RV180W)
- Configuring Jumbo Frames
- Choosing the Routing Mode
- Viewing Routing Information
- Configuring Static Routes
- Configuring Dynamic Routing
- Configuring the IP Mode
- Configuring IPv6 WAN Settings
- Configuring IPv6 LAN Properties
- Configuring IPv6 Routing
- Configuring Tunneling
- Configuring Router Advertisement
- Configuring the Wireless Network (Cisco RV180W)
- Wireless Security Tips
- General Network Security Guidelines
- Enabling Rogue AP Detection
- Authorizing a Rogue AP
- Adding and Editing Authorized APs
- Configuring the Firewall
- Creating an Access Rule
- Adding a Port Triggering Rule
- Adding a Port Forwarding Configuration
- Configuring One-to-One Network Address Translation (NAT)
- Configuring MAC Address Filtering
- Configuring IP/MAC Address Binding
- Creating Custom Services
- Creating Firewall Schedules
- Configuring Sessions
- Configuring Internet Group Management Protocol (IGMP)
- Configuring LAN (Local Network) Groups
- Enabling Session Initiation Protocol Application-Level Gateway (SIP ALG)
- Configuring Virtual Private Networks (VPNs) and Security
- Creating Cisco QuickVPN Client Users
- Configuring a Basic VPN
- Configuring Advanced VPN Parameters
- Configuring VPN Clients
- Monitoring VPN Tunnel Status
- Configuring VPN Users
- Configuring VPN Passthrough
- Using SSL Certificates for Authentication
- Using the Cisco RV180/RV180W With a RADIUS Server
- Configuring 802.1x Port-Based Authentication
- Configuring Quality of Service (QoS)
- Administering Your Cisco RV180/RV180W
- Configuring Web Access
- Configuring User Accounts
- Setting the Session Timeout Value
- Configuring SNMP
- Configuring Additional SNMP Information
- Configuring Logging Policies
- Configuring Firewall Logs
- Configuring Remote Logging
- Configuring Bonjour
- Configuring UPnP
- Viewing the Cisco RV180/RV180W Status
- Using Cisco QuickVPN for Windows 7, 2000, XP, or Vista
- Installing from the CD-ROM
- Downloading and Installing from the Internet
- Where to Go From Here
Configuring the Wireless Network (Cisco RV180W)
Understanding the Cisco RV180W’s Wireless Networks
Cisco RV180/RV180W Administration Guide 61
3
DRAFT - CISCO CONFIDENTIAL
Understanding the Cisco RV180W’s Wireless Networks
The Cisco Small Business RV 120W Wireless-N VPN Firewall provides four
separate virtual wireless networks. These networks can be configured and
enabled with individual settings. You can set up the multiple networks to segment
the network traffic, to allow different levels of access, such as guest access, or to
allow access for different functions such as accounting, billing, and so on.
Configuring Basic Wireless Settings
The following sections contain information on how to configure basic wireless
settings on the Cisco RV180/RV180W. These settings apply to all of the wireless
networks.
Configuring Radio, Mode, and Channel Settings
STEP 1 Choose Wireless > Basic Settings.
STEP 2 In the Radio field, choose Enable to enable wireless functionality for the
Cisco RV180/RV180W. Choosing Disable turns off wireless functionality for the
firewall.
STEP 3 In the Wireless Network Mode field, choose the type of wireless network based
on the devices you have that will connect to the network:
• B/G Mixed—Select this mode if you have devices in the network that
support 802.11b and 802.11g.
• G Only—Select this mode if all devices in the wireless network only support
802.11g.
• B/G/N Mixed—Select this mode if you have devices in the network that
support 802.11b, 802.11g and 802.11n.
• N Only—Select this mode only if all devices in the wireless network support
802.11n.
• G/N Mixed—Select this mode if you have devices in the network that
support 802.11g and 802.11n.
STEP 4 Select the channel bandwidth. Available choices depend on the wireless network
mode chosen in Step 3.