User's Manual

ManualsBrandsSercomm ManualsElectronicsZ-Wave Motion Sensor

SW-PIR03N Z-Wave Motion Sensor Installation Guide

SW-PIR03N is a PIR (Passive Infrared) sensor, which can detect levels of infrared radiation from objects in its range of view. This

Motion Detector is fully compatible with any Z-Wave controller and can be operated in any Z-Wave network with other Z-Wave

certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of

vendor to increase reliability of the network."

It is also a pet immune motion sensor, which is used to ignore the motion caused by animals and thus reduce the likelihood of false

alarms. The sensitivity of the sensor will disregard the motion caused by animals under 85 pounds, like a full-grown dog or small

cats.

In addition, the SW-PIR03N has walk test mode and white light immunity, which can be used to reduce false alarms caused by

lights, flashlights or other reflective objects. These outstanding features of the sensor provides the professional security for

protecting any home or business to save time, money and deliver a great surveillance experience as well.

Specification

Frequency

908.4~916 MHz

Battery Type

GP CR123A * 1

RF Transmission Range

Outdoor: 60 Meters

Temperature Sensor

±1 C Accuracy

Rearm Timer

3 Minutes

Operating Temperature

0 C to 50 C (32° - 122°F)

Storage Temperature

-20 C to 65 C (-4° - 149°F)

Battery Life

2 Years (Assume 30 trigger events per day @25°C)

Dimensions (H xW x D)

93.4mm x 50mm x 31.8mm

Detect Range

Distance: Max. 15M (±1M) w/mounting height 1.8M @25°C

Angle: Max. 90 (±10) Degree @25°C

Package Contents

Installation

1. Detach the mount bracket from the device.

2. Install the provided battery correctly.

3. Attach the mount bracket back to the device.

Summary of content (7 pages)

PAGE 1
SW-PIR03N Z-Wave Motion Sensor Installation Guide SW-PIR03N is a PIR (Passive Infrared) sensor, which can detect levels of infrared radiation from objects in its range of view. This Motion Detector is fully compatible with any Z-Wave controller and can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
PAGE 2
Operation 1. PIR LED (Red) 5. Pairing LED (Green) 2. Tamper Switch 6. Battery Cover (Wall Mount Bracket) 3. Jumper (Walk Test) 4. Battery  Remove the protection film on front panel before installation.  When the battery is installed, the PIR LED will be blinking for 30 seconds and then turn off when the Motion Sensor is ready to be used.  After the tamper switch is pressed, the Motion Detector will be in normal mode.
PAGE 3
Every group can be support to associated 5 devices max. GROUP 1 is lifeline service that assigned to Sensor (Motion detector) status – Open/Close. It enables the sensor to send reports and readings to a Z-Wave Controller or Z-Wave Gateway whenever the sensor is triggered. This Group Support: NOTIFICATION_REPORT_V4 DEVICE_RESET_LOCALLY_NOTIFICATION COMMAND_CLASS_SENSOR_MULTILEVEL_V7 BATTERY_REPORT GROUP 2 allows for Sending Basic to associated devices in this group.
PAGE 4
Mounting Instruction The recommended mounted position for a Motion Detector should be 1.8M from the floor in the corner of a room. At this height, the device can detect a movement up to 15M (±1M ) (see the following image). Also, in this position, the 90 degrees (±10 degree) fan-shaped detection pattern can normally offer greater protection than mounting on a flat wall. Before selecting a position, the following installation hints should be noted: 1.
PAGE 5
Wall Mounting Note: The device is suggested to be set at 90 degrees angle, which is the best mounted position for offering the 15M protection area. 4. 5. Detach the mount bracket from the device. Mount the bracket with the supplied screws/anchors into the wall. It can be either mounted on a flat surface or in a corner. Note: Make sure the mount bracket is installed in the correct direction (upwards arrow). 6. Attach the device to the mount bracket.
PAGE 6
Z-Wave Command Classes • • • • • • • • • • • • • • COMMAND_CLASS_ZWAVEPLUS_INFO COMMAND_CLASS_VERSION COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_BATTERY COMMAND_CLASS_NOTIFICATION COMMAND_CLASS_ASSOCIATION COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_BASIC COMMAND_CLASS_WAKE_UP COMMAND_CLASS_FIRMWARE_UPDATE_MD COMMAND_CLASS_SENSOR_MULTILEVEL COMMAND_CLASS_CONFIGURATION Z-Wave Configuration Configuration Parameter Function Size (Byte)
PAGE 7
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.